95 R2 Single
#1
Full Member
Thread Starter
Join Date: Nov 2003
Location: virginia
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
95 R2 Single
I just finished my FD with single setup and I was wondering if anyone here would load picture for me. File is too big and i do not know how to reduce the file.
new mods,
new engine
single gt35r wastegate back to DP
pettit intercooler with custom mounts
fluidyne radiator
fuel system 4- 850cc
aem true boost controler
innovate LC-1
power FC with fc-loggit
carbonfiber drive shaft
exedy twin disk
tial 44mm WG
tial 50mm bov
racing beat dual tip exhaust
batter relocation
air pump delete
aluminum pullies etc... yadayada....
new mods,
new engine
single gt35r wastegate back to DP
pettit intercooler with custom mounts
fluidyne radiator
fuel system 4- 850cc
aem true boost controler
innovate LC-1
power FC with fc-loggit
carbonfiber drive shaft
exedy twin disk
tial 44mm WG
tial 50mm bov
racing beat dual tip exhaust
batter relocation
air pump delete
aluminum pullies etc... yadayada....
#5
Senior Member
Join Date: Jul 2005
Location: Lancaster, NY
Posts: 520
Likes: 0
Received 0 Likes
on
0 Posts
just a bit of constructive criticism....you need bigger secondary injectors and an upgraded fuel pump for that setup...just looking out for you. I also use the same intercooler and i absolutly love it, your engine bay looks very clean as well. good job!!
#6
Full Member
Thread Starter
Join Date: Nov 2003
Location: virginia
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
Yes, I might need bigger injectors but I did it this way because I'm only going to use pump gas. I do have bigger fuel pump in the car.
#7
Saiga-12 Power!
iTrader: (4)
Join Date: Oct 2004
Location: N of Chicago
Posts: 4,384
Likes: 0
Received 0 Likes
on
0 Posts
Why?
Not sure why you think that because your running pump gas you don't need larger injectors, because you will... Throw some 1680cc injectors in the secondaries and your set. Its always better to have more fuel capacity than you need, than running the bare minimum.
Not sure why you think that because your running pump gas you don't need larger injectors, because you will... Throw some 1680cc injectors in the secondaries and your set. Its always better to have more fuel capacity than you need, than running the bare minimum.
Trending Topics
#10
Senior Member
Join Date: Jul 2005
Location: Lancaster, NY
Posts: 520
Likes: 0
Received 0 Likes
on
0 Posts
I really didnt make "mounts" for the intercooler, i did however take a piece of weather stripping and epoxied it to the crossmember so the intercooler wouldnt rattle. It seems to work fine so far. Please get some 1600cc secondaries, it will save you a lot of head aches rebuilding again, pump gas or not.
#16
development
#19
Full Member
Thread Starter
Join Date: Nov 2003
Location: virginia
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
aem tru boost controller on pillar
innovate xd16 with LC-1 hooked up to dataloggit.
here are some pictures. I was thinking if I could feed analog signal output to power-fc through factory O2 sensor wire in engine bay. Will this analog output from dataloggit work with power-fc? I know, innovate xd-16 is feeding signal to dataloggit, so should this work?
anyway here are some pics.
innovate xd16 with LC-1 hooked up to dataloggit.
here are some pictures. I was thinking if I could feed analog signal output to power-fc through factory O2 sensor wire in engine bay. Will this analog output from dataloggit work with power-fc? I know, innovate xd-16 is feeding signal to dataloggit, so should this work?
anyway here are some pics.
Thread
Thread Starter
Forum
Replies
Last Post
demetlaw
3rd Generation Specific (1993-2002)
6
10-02-15 06:22 PM