352whp @ 14psi - low or normal for GT35R?
#126
F'n Newbie...
iTrader: (6)
Well 6 months have passed since i originally posted this thread and i figured i'd post a quick status update in case people still thought my tune was crap. I've put about 5000 miles on the car since the tune and even had a chance to do a few laps at Pocono FUSA which is a FAST track considering the back straight is part of the NASCAR oval. I'm happy to report that the car still runs just as well as the day i got it tuned even after many redline/full boost pulls. No cold/hot starting issues. No lumpy idle or low speed jerkiness. Needless to say, i'm still very happy with the tune and glad i didn't bother with getting it retuned. Not to open up a can of worms or anything, but if a car can run this well with a "crappy tune", then perhaps "crappy tune" needs to be redefined.
I'll report back in another 6 months...hopefully it'll be a simple copy/paste of this post.
I'll report back in another 6 months...hopefully it'll be a simple copy/paste of this post.
#127
wannaspeed.com
iTrader: (23)
Thanks for updating this mess of a thread OP.
I disagree with the comments that if a hiccup happens it doesn't matter if you're tuned 11:1 or 12:1. Obviously if your hiccup is a failed injector it probably won't matter much, or if someone pours sugar in your gas tank, those hiccups would result in the same damage regardless of AFR, but if you're tuned on the edge and you get a bad tank of gas, you're much safer tuned conservatively than on the edge. If you're running race fuel this is of little concern, but in a real world street car on pump gas things like this can and do happen.
Other things like overboost from a vacuum line coming loose, a piece of carbon glowing on the rotor surface, excessive intake temps, and many other things can be the difference between surviving the hiccup or not.
As far as power made, T3 housing, restrictive exhaust, stock ports, unknown other components. 350 sounds about right to me. I didn't look at the map or anything, but sounds like timing is base PFC timing, it's already on the lean side so I'm not sure how the tuner could get more power without putting the engine at even more risk.
11.7 afr @14 psi is a little on the lean side, but not really overly extreme. I would be happier around 11.3 and would probably set a definite limit of 11.5, but 11.7 is okay as long as you can always count on your fuel being of quality. I personally recommend a water injection kit for anyone running over 12 psi. With Aux injection i wouldn't be surprised if 12.5 was a safe tune (though I still wouldn't tune that lean) it would definitely make me feel better about 11.7 though.
As far as interpolation between the cells, having numbers going all over the place is just not professional, you might get your AFR's in line, but its just tacky and makes reading the map and tuning more difficult. Sloppy things like this just shouldn't come from a professional. It's like watching your fast food handler pick their nose and then hand you the food, maybe it doesn't change the flavor of your food, but its gross, unprofessional and makes you second guess everything else about the food.
I disagree with the comments that if a hiccup happens it doesn't matter if you're tuned 11:1 or 12:1. Obviously if your hiccup is a failed injector it probably won't matter much, or if someone pours sugar in your gas tank, those hiccups would result in the same damage regardless of AFR, but if you're tuned on the edge and you get a bad tank of gas, you're much safer tuned conservatively than on the edge. If you're running race fuel this is of little concern, but in a real world street car on pump gas things like this can and do happen.
Other things like overboost from a vacuum line coming loose, a piece of carbon glowing on the rotor surface, excessive intake temps, and many other things can be the difference between surviving the hiccup or not.
As far as power made, T3 housing, restrictive exhaust, stock ports, unknown other components. 350 sounds about right to me. I didn't look at the map or anything, but sounds like timing is base PFC timing, it's already on the lean side so I'm not sure how the tuner could get more power without putting the engine at even more risk.
11.7 afr @14 psi is a little on the lean side, but not really overly extreme. I would be happier around 11.3 and would probably set a definite limit of 11.5, but 11.7 is okay as long as you can always count on your fuel being of quality. I personally recommend a water injection kit for anyone running over 12 psi. With Aux injection i wouldn't be surprised if 12.5 was a safe tune (though I still wouldn't tune that lean) it would definitely make me feel better about 11.7 though.
As far as interpolation between the cells, having numbers going all over the place is just not professional, you might get your AFR's in line, but its just tacky and makes reading the map and tuning more difficult. Sloppy things like this just shouldn't come from a professional. It's like watching your fast food handler pick their nose and then hand you the food, maybe it doesn't change the flavor of your food, but its gross, unprofessional and makes you second guess everything else about the food.
#128
rotorhead
iTrader: (3)
Just a little FYI to anyone reading who has the default PFC leading and trailing timing maps: I've explained in another thread in the 3rd gen section that you can increase the safety margin of the timing by retarding your trailing (increasing split).
The basemap trailing timing on the PFC model #414-Z004 , the model that most people have, is less safe once you get over about 10psi (and the timing progression is sloppy). But the safety aspect is correctable even with a Commander just by tediously going through the IGT screen, rows P16-P18 (8.5psi to 14 psi range), and retarding the timing (decrease the timing value) by about 4 degrees in every cell over say 2400 rpm (N7 and higher columns in the commander). So take whatever value is in a particular cell, subtract 4 from it, and then input that new value in the cell.
#129
Rotary Freak
iTrader: (8)
11.7@14psi is not really that lean.
I tune a lot of cars these day's and just recently saw a workshop tune a car which I retuned a few days later and car was running 12.5s at 18psi on pump fuel. Engine survived with no issues. I obviously did not leave it there, i usually tune as rich as possible without compromising ignition.
I tune a lot of cars these day's and just recently saw a workshop tune a car which I retuned a few days later and car was running 12.5s at 18psi on pump fuel. Engine survived with no issues. I obviously did not leave it there, i usually tune as rich as possible without compromising ignition.
#130
Enthusiast
iTrader: (5)
11.7@14psi is not really that lean.
I tune a lot of cars these day's and just recently saw a workshop tune a car which I retuned a few days later and car was running 12.5s at 18psi on pump fuel. Engine survived with no issues. I obviously did not leave it there, i usually tune as rich as possible without compromising ignition.
I tune a lot of cars these day's and just recently saw a workshop tune a car which I retuned a few days later and car was running 12.5s at 18psi on pump fuel. Engine survived with no issues. I obviously did not leave it there, i usually tune as rich as possible without compromising ignition.
#131
******
iTrader: (7)
Join Date: May 2009
Location: miami
Posts: 901
Likes: 0
Received 0 Likes
on
0 Posts
11.7@14psi is not really that lean.
I tune a lot of cars these day's and just recently saw a workshop tune a car which I retuned a few days later and car was running 12.5s at 18psi on pump fuel. Engine survived with no issues. I obviously did not leave it there, i usually tune as rich as possible without compromising ignition.
I tune a lot of cars these day's and just recently saw a workshop tune a car which I retuned a few days later and car was running 12.5s at 18psi on pump fuel. Engine survived with no issues. I obviously did not leave it there, i usually tune as rich as possible without compromising ignition.
#132
Rotor Head Extreme
iTrader: (8)
11.7@14psi is not really that lean.
I tune a lot of cars these day's and just recently saw a workshop tune a car which I retuned a few days later and car was running 12.5s at 18psi on pump fuel. Engine survived with no issues. I obviously did not leave it there, i usually tune as rich as possible without compromising ignition.
I tune a lot of cars these day's and just recently saw a workshop tune a car which I retuned a few days later and car was running 12.5s at 18psi on pump fuel. Engine survived with no issues. I obviously did not leave it there, i usually tune as rich as possible without compromising ignition.
When Mazda tuned the fd, I'm sure they took all that into account. Bone stock Fd recommended 91 octane but could still run safely with 87 (though not recommended). I drove mine around for a yr and a half with 87 in the tank without issues. Mazda couldn't put a product out in the market that couldnt run on all available fuels. I guess thats why they tuned so pig rich in the 1st place to make 87 safe. So are you tuners treating your tunes with the same respects?
#137
Eh
iTrader: (56)
Assuming a cost difference of $.30 between 87 and 93 you would save a whopping $200.00 every 10,000 miles at 15mpg. The way we all drive our cars we would save about $40.00 bucks a year.
#139
Rotor Head Extreme
iTrader: (8)
I don't understand why you would go that route or waste the time? I'm sure getting a bad tank of gas can happen but I think that is a tuner excuse 99.9% of the time and not reality.
Assuming a cost difference of $.30 between 87 and 93 you would save a whopping $200.00 every 10,000 miles at 15mpg. The way we all drive our cars we would save about $40.00 bucks a year.
The point is making it safe for all available fuel grades (just like stock) and not having to worry about ONLY putting in a specific fuel grade. It's not just about cost difference either as sometimes 93 may not be available. If a lower grade, is all thats available, then the driver is gonna be paranoid and take things easy until they find their grade. I've noticed more gas stations only carrying 87 recently. I just feel that we would have a lot less blown engines if more tunes took into account all the available fuel grades and not just whatever you tuned with in the 1st place.
I did my own experiement with my stock car for curiosity reasons and was paranoid in the beginning while doing it. I then realized that Mazda obviously took into account that the engine would need to run reliabily on 87 and I stopped worrying about. It's just added piece of mind that's all.
I just figure if more consideration was given to being able to run with lower grades, then we would probably have far less blown engines.
Thread
Thread Starter
Forum
Replies
Last Post
ZaqAtaq
New Member RX-7 Technical
2
09-05-15 08:57 PM