Time for wheelies!
Thread Starter
Joined: Nov 2006
Posts: 4,148
Likes: 4
From: California
Just got back from Irwindale. I Almost made a 7 second pass. My best time was an 8.075 @ 85.35mph. I still need to work on my launching and the 7 second pass will come. The new carb setup helped out alot. I went from 8.2 to 8.0 and from 83mph to 85mph. Here's the timeslip. I got vids too and I will post tomorrow after I edit- too damned tired right now.
Rotary Freak
Joined: Oct 2001
Posts: 1,568
Likes: 2
From: N.J. USA
Just got back from Irwindale. I Almost made a 7 second pass. My best time was an 8.075 @ 85.35mph. I still need to work on my launching and the 7 second pass will come. The new carb setup helped out alot. I went from 8.2 to 8.0 and from 83mph to 85mph. Here's the timeslip. I got vids too and I will post tomorrow after I edit- too damned tired right now.
SFRacing
Joined: Nov 2003
Posts: 41
Likes: 0
From: Los Angeles
Thread Starter
Joined: Nov 2006
Posts: 4,148
Likes: 4
From: California
Ok, Ok, here's the vid, but first let me tell you before you say it. Yes my burnouts sucked because I don't have my line lock installed yet and they get pissed for burning out pass the tree and yes I am granny shifting like a **** I know. 
The first pass was my 8.07- my dad did not get the board at the end because he was getting used to my camera. The second run was my highest mph at 85.6mph but I spun a little in first and second- hard to tell in the vid. The third run I played with the tune a little and went slower and then I ran out of time. The green rx3 is a member here- pportrx3 and he is running a 13bpport and ran really good. Steve, I hope your cool with me putting your run in my vid. Any comments welcomed. Enjoy.
http://www.youtube.com/watch?v=iF36CI5jCHo
The first pass was my 8.07- my dad did not get the board at the end because he was getting used to my camera. The second run was my highest mph at 85.6mph but I spun a little in first and second- hard to tell in the vid. The third run I played with the tune a little and went slower and then I ran out of time. The green rx3 is a member here- pportrx3 and he is running a 13bpport and ran really good. Steve, I hope your cool with me putting your run in my vid. Any comments welcomed. Enjoy.
http://www.youtube.com/watch?v=iF36CI5jCHo
Last edited by ultimatejay; Dec 12, 2008 at 10:18 PM.
Thread Starter
Joined: Nov 2006
Posts: 4,148
Likes: 4
From: California
Joined: Dec 2006
Posts: 1,763
Likes: 0
From: bayamon pr, orlando fl, paterson nj
Ok, Ok, here's the vid, but first let me tell you before you say it. Yes my burnouts sucked because I don't have my line lock installed yet and they get pissed for burning out pass the tree and yes I am granny shifting like a **** I know.
The first pass was my 8.07- my dad did not get the board at the end because he was getting used to my camera. The second run was my highest mph at 85.6mph but I spun a little in first and second- hard to tell in the vid. The third run I played with the tune a little and went slower and then I ran out of time. The green rx3 is a member here- pportrx3 and he is running a 13bpport and ran really good. Steve, I hope your cool with me putting your run in my vid. Any comments welcomed. Enjoy.
http://www.youtube.com/watch?v=iF36CI5jCHo
The first pass was my 8.07- my dad did not get the board at the end because he was getting used to my camera. The second run was my highest mph at 85.6mph but I spun a little in first and second- hard to tell in the vid. The third run I played with the tune a little and went slower and then I ran out of time. The green rx3 is a member here- pportrx3 and he is running a 13bpport and ran really good. Steve, I hope your cool with me putting your run in my vid. Any comments welcomed. Enjoy.
http://www.youtube.com/watch?v=iF36CI5jCHo
looks great keep it up , now your having fun a puto
Rotary Freak
Joined: Oct 2001
Posts: 1,568
Likes: 2
From: N.J. USA
Jay, one thing you need really BAD!!! it will improve your E.T. in great numbers. You need to put that MSD 6AL on the trailing plugs and put the rev limiter chip to about 10,200 rpms and launch on the limiter!!!! make adjustments to the limiter according to your 60ft mark this will be trial and error, if you improve a tenth in your 60 ft mark. you usually pick up 2 tenth's in your E.T.
over all you get a B- grandma shifting not exceptable... sweet runs ... like allen said engine was pulling good in between shifts...
over all you get a B- grandma shifting not exceptable... sweet runs ... like allen said engine was pulling good in between shifts...
Thread Starter
Joined: Nov 2006
Posts: 4,148
Likes: 4
From: California
Jay, one thing you need really BAD!!! it will improve your E.T. in great numbers. You need to put that MSD 6AL on the trailing plugs and put the rev limiter chip to about 10,200 rpms and launch on the limiter!!!! make adjustments to the limiter according to your 60ft mark this will be trial and error, if you improve a tenth in your 60 ft mark. you usually pick up 2 tenth's in your E.T.
over all you get a B- grandma shifting not exceptable... sweet runs ... like allen said engine was pulling good in between shifts...
over all you get a B- grandma shifting not exceptable... sweet runs ... like allen said engine was pulling good in between shifts...
Thanks Manny and Ito, I'll definetely do those things.
Rotary Freak
Joined: Oct 2001
Posts: 1,568
Likes: 2
From: N.J. USA
Senior Member
Joined: Nov 2005
Posts: 392
Likes: 1
From: los angeles
Just got back from Irwindale. I Almost made a 7 second pass. My best time was an 8.075 @ 85.35mph. I still need to work on my launching and the 7 second pass will come. The new carb setup helped out alot. I went from 8.2 to 8.0 and from 83mph to 85mph. Here's the timeslip. I got vids too and I will post tomorrow after I edit- too damned tired right now.
Thread Starter
Joined: Nov 2006
Posts: 4,148
Likes: 4
From: California
Thanks Joe, I guess I just missed you at the track by one week. I was going to go the week you went but my dad couldn't make it. I really wanted so see you run again and the chop top r100. Did you guys get any vids of your runs?
Thread Starter
Joined: Nov 2006
Posts: 4,148
Likes: 4
From: California
SFRacing
Joined: Nov 2003
Posts: 41
Likes: 0
From: Los Angeles
thanks. that pass was 1.45. i think it could have been better but i was having problems with the clutch engaging before i let out pedal. car was creeping forward when i rev it up so i could not get up to launching rpm
SFRacing
Joined: Nov 2003
Posts: 41
Likes: 0
From: Los Angeles
Senior Member
Joined: Nov 2005
Posts: 392
Likes: 1
From: los angeles
what's up judge hope everything is going good with you ! I been busy with work and
church. I recently moved bought my new home , i been on the side lines watching
the import invasion from pr uufff. i had a little time off two weeks ago and went to the track made two runs . first pass was a shake down pass after 8 months of inactivity for me and the car ,the second pass was 5.78@107 very soft on the throttle (sin el budin puesto)very rich . Rene put his onbord camera but came out with no sound check it .
http://www.youtube.com/watch?v=XgcShmscisc
church. I recently moved bought my new home , i been on the side lines watching
the import invasion from pr uufff. i had a little time off two weeks ago and went to the track made two runs . first pass was a shake down pass after 8 months of inactivity for me and the car ,the second pass was 5.78@107 very soft on the throttle (sin el budin puesto)very rich . Rene put his onbord camera but came out with no sound check it .
http://www.youtube.com/watch?v=XgcShmscisc
Last edited by rotorious13b; Dec 13, 2008 at 07:36 PM.