New Website - Who's the QUICKEST in the rotary world?
03-07-09, 03:53 AM
#1
Stay tuned...
Thread Starter
iTrader: (3)
Join Date: Jul 1997
Location: West Islip, Long Island NY
Posts: 2,917
Likes: 0
Received 1 Like
on
1 Post
New Website - Who's the QUICKEST in the rotary world?
When you guys get a chance, check out the site below, excuse the layout, it's just a start....
http://www.worldsquickest.com
Anthony
http://www.worldsquickest.com
Anthony
03-11-09, 12:41 PM
#7
Rotary Enthusiast
Yo my Rx3....
full OG stock chassis and suspesion with stock bolts VERY TRUE ,LOL,9"on leaf springs and traction bars.....NO JOKE
13B turbo
Microtech management
G-Force GF-2000(finally in after years of saving)
26X8.5 inch slick
Methanol
best 60ft 1.23
best 1/8 5.32@133
best 1/4 8.700@157 (bad turbo same weekend i race PICA 06)
best 1/4 trap speed 160 (2004)
Rx3 been sitting since the last time i raced PICA and blew my turbo 2006.Engine was replaced from backup,replaced the turbo recently,tranny and new ignition setup...Suspension is still stock so we will see if i can go out again,this new setup is making a ton more horepower just need to figure out the traction.
full OG stock chassis and suspesion with stock bolts VERY TRUE ,LOL,9"on leaf springs and traction bars.....NO JOKE
13B turbo
Microtech management
G-Force GF-2000(finally in after years of saving)
26X8.5 inch slick
Methanol
best 60ft 1.23
best 1/8 5.32@133
best 1/4 8.700@157 (bad turbo same weekend i race PICA 06)
best 1/4 trap speed 160 (2004)
Rx3 been sitting since the last time i raced PICA and blew my turbo 2006.Engine was replaced from backup,replaced the turbo recently,tranny and new ignition setup...Suspension is still stock so we will see if i can go out again,this new setup is making a ton more horepower just need to figure out the traction.
Trending Topics
03-11-09, 10:29 PM
#8
Auto Pilot
Join Date: Jun 2006
Location: Tbar, Australia
Posts: 74
Likes: 0
Received 0 Likes
on
0 Posts
You may also want to check this thread on Ausrotary for more up to date times than the other list on mazdarotary.net . Its still maintained by the same guy he mentions on his page.
Good idea though, will have to bookmark
Good idea though, will have to bookmark
03-15-09, 12:44 PM
#10
InsaneRotaries.com
^ The list for cars like Sporty and others in the same class, is not completed..
*digs through glove box for Gtech time slip so Anthony could post my "record" time*
*digs through glove box for Gtech time slip so Anthony could post my "record" time*
03-23-09, 05:36 AM
#11
Senior Member
Join Date: Nov 2004
Location: England
Posts: 383
Likes: 0
Received 0 Likes
on
0 Posts
Updates from this weekend of racing here in the UK.
Chris Impey has converted his car to 3/4 chassis, airshifted box, so was shaking down the car and tuning the chassis did a 1.3 60ft
8.8 @ 156
Would you believe this is the first Rotary powered car in the UK to hit an 8, so we are all happy over here on this side of the Pod
On the IRS front, Smiler (James Willaday), Rx7 FD, 13B REW Half bridge,HKS six speed box,C16, 20 PSI on a T88 34D done 1.7 60ft but hooked up 2nd and 3rd well with no wheel spin did a
10.1 @139 nearly nearly a 9 second run.
Myself have improved my personal best still getting used to the extra power and learning to shift quicker managed a 1.6 60ft and done a 11.005 @ 126 at 16psi, I did another 11.04 run but had clutch adjustment problems so called it a day, still won my class and a trophy.
I did quite a few 11.1s earlier so at least im consistant lol, more seat time Im sure I will get my ten
Chris Impey has converted his car to 3/4 chassis, airshifted box, so was shaking down the car and tuning the chassis did a 1.3 60ft
8.8 @ 156
Would you believe this is the first Rotary powered car in the UK to hit an 8, so we are all happy over here on this side of the Pod
On the IRS front, Smiler (James Willaday), Rx7 FD, 13B REW Half bridge,HKS six speed box,C16, 20 PSI on a T88 34D done 1.7 60ft but hooked up 2nd and 3rd well with no wheel spin did a
10.1 @139 nearly nearly a 9 second run.
Myself have improved my personal best still getting used to the extra power and learning to shift quicker managed a 1.6 60ft and done a 11.005 @ 126 at 16psi, I did another 11.04 run but had clutch adjustment problems so called it a day, still won my class and a trophy.
I did quite a few 11.1s earlier so at least im consistant lol, more seat time Im sure I will get my ten
03-27-09, 02:07 AM
#12
Stay tuned...
Thread Starter
iTrader: (3)
Join Date: Jul 1997
Location: West Islip, Long Island NY
Posts: 2,917
Likes: 0
Received 1 Like
on
1 Post
Updates from this weekend of racing here in the UK.
Chris Impey has converted his car to 3/4 chassis, airshifted box, so was shaking down the car and tuning the chassis did a 1.3 60ft
8.8 @ 156
Would you believe this is the first Rotary powered car in the UK to hit an 8, so we are all happy over here on this side of the Pod
On the IRS front, Smiler (James Willaday), Rx7 FD, 13B REW Half bridge,HKS six speed box,C16, 20 PSI on a T88 34D done 1.7 60ft but hooked up 2nd and 3rd well with no wheel spin did a
10.1 @139 nearly nearly a 9 second run.
Myself have improved my personal best still getting used to the extra power and learning to shift quicker managed a 1.6 60ft and done a 11.005 @ 126 at 16psi, I did another 11.04 run but had clutch adjustment problems so called it a day, still won my class and a trophy.
I did quite a few 11.1s earlier so at least im consistant lol, more seat time Im sure I will get my ten
Chris Impey has converted his car to 3/4 chassis, airshifted box, so was shaking down the car and tuning the chassis did a 1.3 60ft
8.8 @ 156
Would you believe this is the first Rotary powered car in the UK to hit an 8, so we are all happy over here on this side of the Pod
On the IRS front, Smiler (James Willaday), Rx7 FD, 13B REW Half bridge,HKS six speed box,C16, 20 PSI on a T88 34D done 1.7 60ft but hooked up 2nd and 3rd well with no wheel spin did a
10.1 @139 nearly nearly a 9 second run.
Myself have improved my personal best still getting used to the extra power and learning to shift quicker managed a 1.6 60ft and done a 11.005 @ 126 at 16psi, I did another 11.04 run but had clutch adjustment problems so called it a day, still won my class and a trophy.
I did quite a few 11.1s earlier so at least im consistant lol, more seat time Im sure I will get my ten
03-27-09, 05:35 AM
#13
Senior Member
Join Date: Nov 2004
Location: England
Posts: 383
Likes: 0
Received 0 Likes
on
0 Posts
Just fitted new plates to the OS Giken twin plate, there is an adjustable rod thats in the slave cylinder that activates the push pull convertor, if the rod is too long, the clutch fork makes it ride against the release bearing and the clutch is not fully engaged so at certain torque levels it will slip, so on my high boost run of 1.25 bar the clutch slipped all the way in 3rd and 4th gear,
So adjusted the rod for the final run but the clutch grabbed really hard and not enough revs and I bogged off the line and still ran a 11.4 lol
So adjusted the rod for the final run but the clutch grabbed really hard and not enough revs and I bogged off the line and still ran a 11.4 lol
04-24-09, 02:36 PM
#14
Anthony, check out this site: http://www.mazdarotary.net/records.htm
You might be able to use some of that info.
You might be able to use some of that info.
I dont see current world records like;
Sporty RX7 6 sec pass
Falito's RX8 recent 7.02 / 194MPH
Pica Imports RX7 and RX8
Anais Starlet quickest 3/4 chasis in the world 7.2 / 191MPH
04-24-09, 03:26 PM
#15
InsaneRotaries.com
dem sarg, seems like you've been away for to long...
Anais record got beaten several times by many different cars.. Right now Adriana is Back holds the record with 7.06 @ 194mph
Even the old girl, La Atrevida is running faster than before..
Anais record got beaten several times by many different cars.. Right now Adriana is Back holds the record with 7.06 @ 194mph
Even the old girl, La Atrevida is running faster than before..
04-25-09, 08:54 PM
#16
ErnieTKiLLA
Join Date: Feb 2002
Location: new york
Posts: 972
Likes: 0
Received 0 Likes
on
0 Posts
Just fitted new plates to the OS Giken twin plate, there is an adjustable rod thats in the slave cylinder that activates the push pull convertor, if the rod is too long, the clutch fork makes it ride against the release bearing and the clutch is not fully engaged so at certain torque levels it will slip, so on my high boost run of 1.25 bar the clutch slipped all the way in 3rd and 4th gear,
So adjusted the rod for the final run but the clutch grabbed really hard and not enough revs and I bogged off the line and still ran a 11.4 lol
So adjusted the rod for the final run but the clutch grabbed really hard and not enough revs and I bogged off the line and still ran a 11.4 lol
I had the same clutch 2 years ago.. best thing i did was take it out nothing but headaches.
04-27-09, 05:14 AM
#17
Senior Member
Join Date: Nov 2004
Location: England
Posts: 383
Likes: 0
Received 0 Likes
on
0 Posts
Ps TurboR1, those front skinnies you sold me are working very well, the car is much easier to handle at the top end of the strip
04-27-09, 06:54 AM
#18
mmm doritos
iTrader: (4)
Join Date: Apr 2006
Location: lancaster PA
Posts: 2,107
Likes: 0
Received 0 Likes
on
0 Posts
looking good man, im assuming your still working on the "Turbo" section? also another thing that would make that list awesome is linking vids if available next to each run. A lot of these people have videos of those passes..
Thread
Thread Starter
Forum
Replies
Last Post
rx8volks
Canadian Forum
0
09-01-15 11:02 PM