Rotary Car Performance General Rotary Car and Engine modification discussions.

13b na mods?

Thread Tools
 
Search this Thread
 
Old 03-14-11, 05:30 PM
  #1  
Junior Member
Thread Starter
 
Dementia's Avatar
 
Join Date: Nov 2010
Location: reno, NV
Posts: 19
Likes: 0
Received 0 Likes on 0 Posts
13b na mods?

What is the first mod that should be done to a stock na 13b motor. Its is a 88gtu
Old 03-14-11, 06:06 PM
  #2  
Junior Member
Thread Starter
 
Dementia's Avatar
 
Join Date: Nov 2010
Location: reno, NV
Posts: 19
Likes: 0
Received 0 Likes on 0 Posts
mod

By mod I mean, the best one for increasing hp and least expensive
Old 03-14-11, 06:36 PM
  #3  
Lenny

iTrader: (9)
 
Len-Len's Avatar
 
Join Date: Mar 2010
Location: Albuquerque
Posts: 472
Likes: 0
Received 2 Likes on 1 Post
First mod to do is use the search button on this site.

Other than that, exhaust and intake.
Old 03-14-11, 06:55 PM
  #4  
Full Member
 
Starbux's Avatar
 
Join Date: Jan 2010
Location: Woodbridge, Va
Posts: 130
Likes: 0
Received 0 Likes on 0 Posts
port!
Old 03-15-11, 02:29 PM
  #5  
Dual Wielding DieGrinders

iTrader: (3)
 
theflatlander's Avatar
 
Join Date: Aug 2002
Location: Elko, NV
Posts: 720
Likes: 0
Received 2 Likes on 2 Posts
Check out the faq threads in the 2nd gen section, with that said is ur 7 in good running condition with full tune-up etc? Might wanna consider that b4 tossing mods at it. And for cheap mods look up throttle body mod w/port n polish, can also port ur intake manifold for a few hp, both are basically free mods.
Old 03-17-11, 01:07 PM
  #6  
Moderator

iTrader: (3)
 
diabolical1's Avatar
 
Join Date: Feb 2002
Location: FL
Posts: 10,817
Received 306 Likes on 267 Posts
1. cleaning/restoration (water cleaning, replace vacuum hoses, etc.)
2. maintenance/tuneup
3. exhaust system

you have a LOT of reading to do.
Old 05-19-11, 02:13 PM
  #7  
Naturally Aspirated
 
D. Gomes's Avatar
 
Join Date: Feb 2011
Location: Marina, Ca
Posts: 73
Likes: 0
Received 0 Likes on 0 Posts
First thing you should be looking to buy is a good quality header.
Old 07-12-12, 08:16 PM
  #8  
Junior Member
 
rfranklin's Avatar
 
Join Date: Mar 2012
Location: GA
Posts: 27
Likes: 0
Received 0 Likes on 0 Posts
I always do exhaust and headers first then get ya a air intake clutch radiator and all tht
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Jeff20B
1st Generation Specific (1979-1985)
73
09-16-18 07:16 PM
befarrer
Old School and Other Rotary
2
10-05-15 03:30 AM
mulcryant
2nd Generation Specific (1986-1992)
10
09-09-15 05:24 PM



Quick Reply: 13b na mods?



All times are GMT -5. The time now is 08:43 AM.