My MX5 Rotary swap
#176
Full Member
Thread Starter
Join Date: Dec 2012
Location: New Zealand
Posts: 198
Likes: 0
Received 0 Likes
on
0 Posts
Thank you CFAMILYFIX, it has been getting expensive and its taking a lot longer than anticipated seeing as this car is the work car lol But all I am waiting for now is that fuel pump and then when he starts it hopefully it returns back to normal and I can bring it home and enjoy it. I am just glad the compression test showed 100psi even on all faces.
#178
Full Member
Thread Starter
Join Date: Dec 2012
Location: New Zealand
Posts: 198
Likes: 0
Received 0 Likes
on
0 Posts
Thanks Wildman923, not down its just I hate using the Supra to work as thats the favorite in my collection RX7 fuel pump arrive today and its fairly freaking big so I am hoping this will cure all fuel issues and get my MX5 running back to normal at 100%
#180
Full Member
Thread Starter
Join Date: Dec 2012
Location: New Zealand
Posts: 198
Likes: 0
Received 0 Likes
on
0 Posts
I will for sure Marques1681, just worries a little at the moment with all the car thieves going around. My friends MX5 was stole chopped and then flipped and left in some ones back yard. Problem is the justice in this country is too soft and the police cant do much with the thieves worries about my MX5 sharing the same fate since it parks outside in my driveway.
#181
Full Member
Thread Starter
Join Date: Dec 2012
Location: New Zealand
Posts: 198
Likes: 0
Received 0 Likes
on
0 Posts
Update time:
Spoke to the guy working on getting my car running as I wanted to drop off the fuel pump and got told that he has far too much work on and hasnt done much to my car meaning the only thing he has done is remove the carb set up So looks like I am going to be waiting a few weeks for him as apparently he doesnt work weekends even with "so much work to make any progress with my car"
Spoke to the guy working on getting my car running as I wanted to drop off the fuel pump and got told that he has far too much work on and hasnt done much to my car meaning the only thing he has done is remove the carb set up So looks like I am going to be waiting a few weeks for him as apparently he doesnt work weekends even with "so much work to make any progress with my car"
#182
Full Member
Thread Starter
Join Date: Dec 2012
Location: New Zealand
Posts: 198
Likes: 0
Received 0 Likes
on
0 Posts
Oh well small update is that everything should be completed by Friday this week meaning stock intake and injectors installed and wired up. Hoping it starts now since the tuner mechanic didnt find the fault and hes been delaying it for 3 weeks now.
#188
Full Member
Thread Starter
Join Date: Dec 2012
Location: New Zealand
Posts: 198
Likes: 0
Received 0 Likes
on
0 Posts
Car is back and doesnt start I will try the ATF trick but according to the tuner which is complete lies but he said it started on the front rotor while he had it but judging that its sat in the same spot when it was dropped off means it was never started nor tow started as he said. He suggested it may be the corner seals?
#190
Full Member
Thread Starter
Join Date: Dec 2012
Location: New Zealand
Posts: 198
Likes: 0
Received 0 Likes
on
0 Posts
Thats what I told him as well, compression is 100psi on all faces with the motor not running on the second rotor so now I have no idea what it is since if the seals were gone it would lose compression
#191
Full Member
iTrader: (1)
That's not sounding right. If a seal was damaged it should drop your compression. If compression is even across all rotor faces that shouldn't be the issue. If your getting fuel to the chamber, and compression is good then it has to be the ignition side of the house.
It's coming along slowly, just recently finished up installing the frame rails, swapping the fuel pump for a 410 lph, re-running the fuel lines in 6AN, and mounting up the new Ethanol sensor. Going to try and finish up the wiring / vacuum routing tomorrow (Wastegate / Boost control solenoid / Ethanol sensor).
It's coming along slowly, just recently finished up installing the frame rails, swapping the fuel pump for a 410 lph, re-running the fuel lines in 6AN, and mounting up the new Ethanol sensor. Going to try and finish up the wiring / vacuum routing tomorrow (Wastegate / Boost control solenoid / Ethanol sensor).
#192
Full Member
Thread Starter
Join Date: Dec 2012
Location: New Zealand
Posts: 198
Likes: 0
Received 0 Likes
on
0 Posts
I honestly think it is the ignition side of things but everyone I speak to say different things. I get good compression but no start so it seems like its the ECU then when I ask someone else they say could be a corner seal, but to me even a corner seal will not give even compression not at all. I am getting spark and fuel as I tested both and I poured some oil into the chambers today to free up any stuck seals so will try starting tomorrow morning.
Awesome Wildman923 hope you get it finished soon
Awesome Wildman923 hope you get it finished soon
#193
Full Member
Thread Starter
Join Date: Dec 2012
Location: New Zealand
Posts: 198
Likes: 0
Received 0 Likes
on
0 Posts
Ok so I am not an expert on the 1B however testing the leading spark plugs yesterday buy removing it from the housing, and the grounding the plug on the throttle body with the injectors unplugged I get a very very weak spark and by weak it is the size of this full stop ( . ). I am not sure if that is enough to ignite the fuel mixture but from working with piston engines I know enough to have seen a good spark am I right in saying the spark would be causing the no start? I have replaced plugs, leads, coil packs so that only leaves the Megasquirt and Bosch igniters that the tuner installed am I on the right track?
#194
Full Member
iTrader: (1)
Ok so I am not an expert on the 1B however testing the leading spark plugs yesterday buy removing it from the housing, and the grounding the plug on the throttle body with the injectors unplugged I get a very very weak spark and by weak it is the size of this full stop ( . ). I am not sure if that is enough to ignite the fuel mixture but from working with piston engines I know enough to have seen a good spark am I right in saying the spark would be causing the no start? I have replaced plugs, leads, coil packs so that only leaves the Megasquirt and Bosch igniters that the tuner installed am I on the right track?
Last edited by Wildman923; 06-02-13 at 07:06 AM.
#195
Full Member
Thread Starter
Join Date: Dec 2012
Location: New Zealand
Posts: 198
Likes: 0
Received 0 Likes
on
0 Posts
Thank you so much Wildman923 I will double check the grounds but I have all factory grounds and a thick ground from body to engine so I am sure I have enough grounding. I think it may be the igniter or ECU but the spark is terrible so I am hoping thats the only problem left to fix. I have changed coil packs, leads and plugs
#197
Full Member
Thread Starter
Join Date: Dec 2012
Location: New Zealand
Posts: 198
Likes: 0
Received 0 Likes
on
0 Posts
I tried tow starting and it just backfired, got home and de-flooded it (the tuner said he did that already but alot of mist came out), after that I havent had a chance to tow start, would I be getting enough spark since the tow start created backfire? I would have thought the back fire is from the over fueling and then small areas igniting since the spark is so weak?