13b turbo in a b2600 4X4
#1
Junior Member
Thread Starter
iTrader: (1)
Join Date: Jun 2009
Location: canada
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
13b turbo in a b2600 4X4
hey everyone, 1st post here, I have done alot of research and have found little info on this swap. what I could not find is if anyone has acually done this swap? I have a 1991 b2600i 4X4 with a cracked head and i wanted to replace the engine with something with a little more power (13b) and keep the original trans/trasfer. If anyone has some input or info i would appreciate it. (buying the engine one week from today if everything goes as planned).
Thanks, Jesse
Thanks, Jesse
#2
Ricer
iTrader: (4)
Shoot an email to Dan Atkins at Atkins rotary (.com) and he will be able to answer alot of your questions. I know there are is a site that sells an engine mount adapter for a 13B into B series trucks. Some other things available also, just cant remember the site. He will be able to point you in the right direction.
#3
Retired Moderator, RIP
iTrader: (142)
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes
on
114 Posts
IF you get the info,it would be Great if you could Post it up on the forum.I was "dreaming" about the same sort of thing.I actually had the Truck,and the engine at the same time,But I was gonna use the truck for Daily driving(4 banger)and the Engine(TII) for my car!
#5
yeah there are vids on you tube of rotary b-series trucks, and yes the trans has to be changed, the starter for a rotary is mounted in the opposite position as it is for the pickup, i considered this project when i was rotorless and wrecked my b2200, but i have a project FC now
#7
Junior Member
Thread Starter
iTrader: (1)
Join Date: Jun 2009
Location: canada
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
thanks for the replies. From what i've read the trans in my b2600 is the same as the 89-91 rx7 tranny, and to do the swap all i would have to do is replace the bell housing, fab up the mounts and fab the exhaust. I didn't know about the starter being on opposite sides? where you comparing it to a b2200? any other info would be greatly appreiciated.
(here is a pic of my truck that will be going 13bt, i can't figure out how to shrink the pic down so just copy and paste the link.)
http://www.nopistons.com/forums/B260...ed#entry923256
(here is a pic of my truck that will be going 13bt, i can't figure out how to shrink the pic down so just copy and paste the link.)
http://www.nopistons.com/forums/B260...ed#entry923256
Trending Topics
#10
Right near Malloy
iTrader: (28)
Join Date: Dec 1999
Location: Behind a workbench, repairing FC Electronics.
Posts: 7,835
Received 502 Likes
on
340 Posts
The SA RX-7 and all N/A RX-7s used a smooth case transmission that does NOT have a seperate bell housing.
He will need a Turbo 2 bell housing.
I have one of these trucks sitting in my back yard.
In addition to the engine swap. Use the Turbo2's differential in the rear end of the truck and an N/A differential in the front. (Not ring and pinion. the 4.44:1 that's stock you'll need for torque. Use the differential for Limited slip/locking capability in the mud.)
#11
Junior Member
Thread Starter
iTrader: (1)
Join Date: Jun 2009
Location: canada
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
Hey, I picked up my engine, trans, and wiring yesterday out of a 90 rx7. right now i've got the old engine out of my truck and the new engine on it's way in. everything looks like the engine will slide in with a few mods. One thing that i didn't think i would have to do is move the trans up about an inch and a half, this isn't for sure but i think the intake is going to hit the fire wall. no big deal though, the drive shafts have a slip yoke so i think i may be able to get away with sloting or redrilling the mounts. if anyone has any experience and wants to chime in i would be happy to here from you.
Thanks
Thanks
#12
Junior Member
Join Date: Mar 2013
Location: lenanon or
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
if there is any one wanting to do this swap still a have done it and kept all the truck running gear and didn't have to drop the front sus. also know what part need to be swaped and what years the right parts have to come out of
#14
Reply
Email is marcusmazda@windowslive.com
cheers
#15
Badass
Bro please email me majmarkmiranda@gmail.com I'm currently gonna do a swap on a 1992 b2600i 4x4 and wanna put a 13b in it maybe a turbo one from my research all I need is a bell housing wiring harness engine and a 13bll from a 89 to 91 rx7 please confirm and tell me what u did
Thread
Thread Starter
Forum
Replies
Last Post
KAL797
Test Area 51
0
08-11-15 03:47 PM