yo izzy you coming on the 21st for teh barbeque?!?

 

i will be down there sometime soon as well ben. now that i am finally going to be working only 1 job i should have much more time. also the fact that it's finally light out.

I GOT MY WIDEBAND TODAY!(it took foreverrrr) now i just need to get it welded on(bennnnn?)

 

what WB is it Andy? most WB have a NB simulation output so you don't need a second bung. just get rid of that nasty old NB sensor and throw the WB in that bung and hook the NBSIM wire up to the harness for the stock NB. i can show you at the meet if you want. i did this on mine.

 

My wideband instructions tell me to put my sensor kinda far from the turbo though..... it actualy wants it to be on the mid pipe. apparently the heat will kill the sensors quickly and not read as accurately.

 

ehhh somewhat kinda true/open to interpretation. i have read that 12-16 inches from the exhaust outlet on the engine it ideal, but i have also seen that the ideal place is as close as possible heat permitting. i have mine right in the racingbeat location and it works no problem/not worried about over heating. i think that the midpipe is a little too far in a free flowing exhaust because at that distance you won't get an accurate reading, once again, or so i have read.

which one did you get?

 

lol yea sorry the pic was so big its a RE kit an its guna be 2 tone black top lambo to flow with the lines the rim is guna get painted lambo orange to match ill put more power as i go but putting on the kit was hard enough i spent like 7 grand so far lol but yea im not sure i can make the meet ill try my best an if i do i dont think ill have the car but ill be back from mexico on the 22 or march so ill need a partner to cruise with

 

sweet sounds like a sexy paint job. when is the paint going on? sorry if you already said this..

 

lol yea sorry the pic was so big its a RE kit an its guna be 2 tone black top lambo to flow with the lines the rim is guna get painted lambo orange to match ill put more power as i go but putting on the kit was hard enough i spent like 7 grand so far lol but yea im not sure i can make the meet ill try my best an if i do i dont think ill have the car but ill be back from mexico on the 22 or march so ill need a partner to cruise with

 

Yeah Ben seriously. Give Izzy and me your number and we will come up to chill all the time. You too Andy.

 

Oh , didnt realize you asked the brand christian, its the Innovate LM-1

 

damn... 3 days guys!

 

ok sorrry i didn't read throught the thread but date and place of meet is???????!!

 

It's on page 77.

 

it's this friday 7 pm check for the adress on the previous page.

 

my friend has the same one and he runs it in the stock location no problem. t2sleeper on here.

 

hey guys, make an account over at rotarycarclub.com!

 

rotarycarclub? meh?

 

it's newer better rx7club!

 

tru. its not the same kit(lc-1) but its the same sensor. havnt had any problems with it in the stock rb location

 

thanks for that link. yeah if you want to chill let me know pm me and we can make plans. iam going away this week end but next week iam free.

 

define this week Ben... your gonna be around for the 21st right?

 

so what do i do with the stock sensor when i put the wideband sensor in the stock location? dont i have to have something hooked up to the wiring harness?

 

yeah, you're WB should have a single wire NB output, look in the manual, run that to the factory harness.

 

ive had an lm1 sence i built my setup, thousands of miles, i run farily high egt's under cruise, still on stock sensor. i think ive got 3 summers out of it

mine has been 12'ish from the turbine outlet, only problems ive had with it is when i heatwrapped my dp. if i parked and shut of the car, sensor would be too warm when i started it back up and throw an error

 

hey Andy, guess what i just got...