Microtech How do you know what series the ECU is?
#1
How do you know what series the ECU is?
Is there some way to know what series your ecu is factory programmed for? Is it programmed for an FC or FD crank setup.
I have an FD and bought a used ecu on here some time ago and have been unable to get the car started. I am wondering if it was not programmed for FD. The only thing I can see on my ecu that many give some idea is that says b2.0 on one of the screens. What is that for?
I have an FD and bought a used ecu on here some time ago and have been unable to get the car started. I am wondering if it was not programmed for FD. The only thing I can see on my ecu that many give some idea is that says b2.0 on one of the screens. What is that for?
#2
Engine, Not Motor
iTrader: (1)
Join Date: Feb 2001
Location: London, Ontario, Canada
Posts: 29,789
Likes: 0
Received 108 Likes
on
91 Posts
You'll find these settings on screen 31.
Specifically the Config settings, Firing, InputTrig, SparkTrig.
If you post these we can give you a good guess as to how it is set up.
Specifically the Config settings, Firing, InputTrig, SparkTrig.
If you post these we can give you a good guess as to how it is set up.
#3
From menory these are options
firing- group fire or sequential
input trig - +ve or -ve
sparktrig - -ve or maz (something like that or maz+)
When cranking i will get spark from the leading plugs when when the SparkTrig is set to Maz only, it doesnt fire when the sparktrig is set to -ve.
Once the sparktrig is set to Maz then it will spark regardless if the input is on +ve or -ve. It will sound like it almost wants to start but just doesnt.
I did a pull start attempt and after some pulling the engine kinda ran but i had to keep my foot on throttle to keep it "running" and it sounded like when you have a dead rotor or bad timing and the red light was blinking for rpm and reference, etc errors.
Its a new build, havent done a compression test yet, but even if a rotar was bad it shouldn't have been throwing the errors i think if all else was ok.
firing- group fire or sequential
input trig - +ve or -ve
sparktrig - -ve or maz (something like that or maz+)
When cranking i will get spark from the leading plugs when when the SparkTrig is set to Maz only, it doesnt fire when the sparktrig is set to -ve.
Once the sparktrig is set to Maz then it will spark regardless if the input is on +ve or -ve. It will sound like it almost wants to start but just doesnt.
I did a pull start attempt and after some pulling the engine kinda ran but i had to keep my foot on throttle to keep it "running" and it sounded like when you have a dead rotor or bad timing and the red light was blinking for rpm and reference, etc errors.
Its a new build, havent done a compression test yet, but even if a rotar was bad it shouldn't have been throwing the errors i think if all else was ok.
Last edited by BluRR; 11-11-17 at 05:08 PM.
#4
Engine, Not Motor
iTrader: (1)
Join Date: Feb 2001
Location: London, Ontario, Canada
Posts: 29,789
Likes: 0
Received 108 Likes
on
91 Posts
I'd need to see the settings exactly as shown. Not as familiar with how the Microtech is set up on the FD however the trigger should be the same as the FC. If I saw them, I'd recognise wrong ones.
Maybe someone else knows off hand.
Maybe someone else knows off hand.
#5
MAPs = Matrix, Normal
Config +04cyl/R
Firing Sequential, GroupFire
Load = MAP sensor, TPS sensor
DWELL= time base, duty cycle
Input Trig +POS, -NEG
Spark Trig Maz+, -NEG
Timing check OFF, LOCK ON
Rpm_ON 1500 Log
Map_ON 10"Hg Log
spare1 +00% Log
spare 2 _00% Log
SHIFT 7060 Dash
WATER 94C Dash
AIR_T 72C Dash
BOOST 12psi Dash
Config +04cyl/R
Firing Sequential, GroupFire
Load = MAP sensor, TPS sensor
DWELL= time base, duty cycle
Input Trig +POS, -NEG
Spark Trig Maz+, -NEG
Timing check OFF, LOCK ON
Rpm_ON 1500 Log
Map_ON 10"Hg Log
spare1 +00% Log
spare 2 _00% Log
SHIFT 7060 Dash
WATER 94C Dash
AIR_T 72C Dash
BOOST 12psi Dash