Microtech Area is for discussing Microtech systems

Microtech Help, too rich.

Thread Tools
 
Search this Thread
 
Old Mar 9, 2003 | 03:49 AM
  #1  
12at's Avatar
Thread Starter
10.21 @ 137mph
Tenured Member 10 Years
 
Joined: Jan 2003
Posts: 184
Likes: 1
From: australia
Help, too rich.

Ok here's my problem,
I have just upgraded turbo's from a high flowed 13b turbo to a Garrett TA45. At the same time I upgraded my injectors from 550 primaries to 720's and from 720 secondaries to 1700's. My problem is I can barely get the car to run as it is so over fuelled. I had to remove the plugs and clean them 4 times just to get it to fire up. I drove the car briefly and you can hardly accelerate at all as it just floods.

I tried taking out the 1700cc injectors and putting some 720's back in the secondaries but it didnt make much difference as anything over 1/4 throttle it would flood still. I did get 2 psi though, lol.

I dont want to run the 4 12a turbo injectors as I want to run 15 psi on the street and more at the track with decent fuel. That is why I got the 1700's.

Is there any way I can alter my fuel map without messing it up completely?

This is on a 12a using a 13b throttle body and an MTX8 with a 3 bar map sensor.

I know it needs to be tuned properly but I would like to be able to at least drive it onto a trailer.

Any advice would be appreciated.
Thanks
Daniel
Reply
Old Mar 9, 2003 | 07:47 AM
  #2  
rxeng's Avatar
Full Member
Tenured Member 05 Years
 
Joined: Mar 2002
Posts: 178
Likes: 3
From: australia
You will have to do a complete re tune.
But if you are just wanting to get it to start & run onto the trailer then try taking fuel out with the mixture trim.
Get the car running & go up 4 clicks on the handset & you will see the Options screen.Mix trim is the first one you will come to.
Try taking 20% out & see how it goes.If it's better keep taking fuel out till it runs the best & leave it at that.
Get it onto the trailer somewhere to get it tuned asap!!
Jon
Reply
Old Mar 9, 2003 | 06:16 PM
  #3  
12at's Avatar
Thread Starter
10.21 @ 137mph
Tenured Member 10 Years
 
Joined: Jan 2003
Posts: 184
Likes: 1
From: australia
Thanks Jon, I'll give it a go.
Reply
Old Mar 11, 2003 | 04:23 AM
  #4  
12at's Avatar
Thread Starter
10.21 @ 137mph
Tenured Member 10 Years
 
Joined: Jan 2003
Posts: 184
Likes: 1
From: australia
Well I did it. I took out 20% like you said and it made it better but it still broke down under more than 1/4 throttle so I took out another 5% and that seemed to do the trick. It even starts off the key again.

Thanks very much Jon.
Reply
Old Mar 12, 2003 | 05:29 AM
  #5  
Anthony Rodrigues's Avatar
Full Member
Tenured Member 05 Years
 
Joined: Mar 2002
Posts: 181
Likes: 0
From: australia
Go to the staging % change this to 99% the stg rpm to 3.5k and the stgmap to 1psi and reduce the mixture trim to -35% and it should have roughly the same as before and should be able to drive. This should help
Regards-Anthony
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
82streetracer
Haltech Forum
11
Mar 11, 2019 05:34 PM
Captain Hook
2nd Generation Specific (1986-1992)
8
Sep 22, 2015 01:12 PM
Monsterbox
Adaptronic Engine Mgmt - AUS
5
Sep 11, 2015 03:29 PM
incubuseva
2nd Generation Specific (1986-1992)
14
Sep 3, 2015 12:37 PM
Rx7marine
Power FC Forum
0
Aug 27, 2015 09:49 PM




All times are GMT -5. The time now is 03:16 AM.