Microtech Area is for discussing Microtech systems

Microtech Engine fires before cranking.

Thread Tools
 
Search this Thread
 
Old 05-19-03, 07:52 PM
  #1  
Rotary Freak

Thread Starter
 
SaabGuy's Avatar
 
Join Date: Oct 2001
Location: Atlanta, GA
Posts: 1,514
Likes: 0
Received 1 Like on 1 Post
Engine fires before cranking.

Sometimes when I turn the key to ignition my engine pops. This seems to happen hot or cold. What is happening is this.

I get in to start the car
put the key in
turn it to ignition (one before CRANK)
a small explosion emits back through the intake manifold.

Makes a pop sound. The microtech says the engine is in a idle state just after this all happens. Seems like some spark plugs are firing at will! Usually when this happens a vacumm cap blows off. I have yet to catch this happening when my foot is on the gas 1/4 while turning the key to ignition.

This has popped 7 times since I installed the microtech.

Last edited by SaabGuy; 05-19-03 at 07:57 PM.
Old 05-19-03, 11:58 PM
  #2  
what 7

 
Piranha's Avatar
 
Join Date: Feb 2002
Location: Portage, MI
Posts: 670
Likes: 0
Received 1 Like on 1 Post
I wonder if you have leaky injectors? The fuel pump primes when you turn the key to on. Just a theory.
Old 05-20-03, 12:03 AM
  #3  
Rick James

 
HIMNI Racing's Avatar
 
Join Date: Sep 2002
Location: Under The Hood In FL
Posts: 631
Likes: 0
Received 0 Likes on 0 Posts
Man has this happened to anyone eles? I don't need this type of stuff to happen to me.

Does anyone know what this is? I too would like to know.

Brandon?
Old 05-20-03, 01:31 AM
  #4  
Rotary Enthusiast

 
10sec rx7's Avatar
 
Join Date: Mar 2001
Location: Sydney, Australia
Posts: 1,350
Likes: 0
Received 8 Likes on 7 Posts
I havent heard of this heppening before, the only reason it would do this is if it is picking up a signal from teh CAS and then would pluse the injectors and the coils,

check you CAS wiring,
Old 05-20-03, 07:12 AM
  #5  
Banned. I got OWNED!!!
 
BlackFC's Avatar
 
Join Date: Sep 2001
Location: Pensacola, FL
Posts: 311
Likes: 0
Received 0 Likes on 0 Posts
No problems here, I did have a problem with my Talon back fireing after i turned it off when I was trying to install a PMS on it once. That was weird enough.

Daniel
Old 05-20-03, 08:20 AM
  #6  
RX-7 Bad Ass

iTrader: (55)
 
DaleClark's Avatar
 
Join Date: Jan 2002
Location: Pensacola, FL
Posts: 15,399
Received 2,437 Likes on 1,508 Posts
It's probably the coils firing - might be getting some sort of surge to the coils that's making them discharge. That could be a tricky one to trace down!

Dale
Old 05-20-03, 10:13 AM
  #7  
Despise Enmity

 
Josepi's Avatar
 
Join Date: May 2001
Location: Richmond, VA
Posts: 2,420
Likes: 0
Received 0 Likes on 0 Posts
What about the 12V wire that's "supposed" to supply power to the coil...could it be mixed up with the signal wire?
Old 05-20-03, 10:27 AM
  #8  
Rotary Freak

Thread Starter
 
SaabGuy's Avatar
 
Join Date: Oct 2001
Location: Atlanta, GA
Posts: 1,514
Likes: 0
Received 1 Like on 1 Post
The wiring checks out. This is on an LT8x unit.

Yes the injectors probably have a small leak, either that or they inject while the motor turns off from the run before.

Dale, I tried moving some of the CAS wires around a little and I reseated the connector at the CAS. Im waiting for this to happen again.


I do notice that my tach kicks just a tiny winsy bit. like it just pulses off of 0 for less that 100th of a second.
Old 05-20-03, 10:35 AM
  #9  
root

 
zyounker's Avatar
 
Join Date: Mar 2001
Location: Phoenix, AZ
Posts: 1,200
Likes: 0
Received 0 Likes on 0 Posts
I noticed on a haltech when you turn the ignition to on, the coils will fire.. (check this using a timming light)


We where having trouble with the coils so i am not sure that is 100% normal though..


We never got a pop though.. check your injectors.. they may be leaking.
Old 05-20-03, 03:55 PM
  #10  
Rotary Freak

Thread Starter
 
SaabGuy's Avatar
 
Join Date: Oct 2001
Location: Atlanta, GA
Posts: 1,514
Likes: 0
Received 1 Like on 1 Post
Or they may not be leaking if the ecu injects fuel continually upon engine shut off.

Or maybe the ecu is injecting fuel when I turn the key to ig. Either way, leaking or not, its still not normal unless Microtech says its normal.

Good advise with the timing light though.
Old 05-29-03, 02:31 PM
  #11  
My Custom Title > Your's

 
COsborne's Avatar
 
Join Date: Feb 2002
Location: Charleston, SC
Posts: 629
Likes: 0
Received 1 Like on 1 Post
my haltech will pop like that sometimes. It definitely sparks the ignition when you give it power b/c I bumped the battery cable to the post and I got a nice little shock in the arm from my leading coils
Old 05-29-03, 10:15 PM
  #12  
Rotary Freak

Thread Starter
 
SaabGuy's Avatar
 
Join Date: Oct 2001
Location: Atlanta, GA
Posts: 1,514
Likes: 0
Received 1 Like on 1 Post
I kind of dont care about this problem anymore. Its bothersome but whatcha gonna do.

I just open the throttle when I turn the key so that my vacumm caps dont bust off.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM
gtcd
1st Generation Specific (1979-1985)
30
08-19-15 02:44 AM
pzr2
General Rotary Tech Support
1
08-15-15 08:29 PM



Quick Reply: Microtech Engine fires before cranking.



All times are GMT -5. The time now is 02:39 PM.