New member from Ireland
#51
Full Member
Thread Starter
Join Date: Nov 2011
Location: Ireland
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
Ok got the drivers section roll cage all bent and cut out
The two section all welded and lower section
Speakers all in
Front windscreen closing panel painted
Metal section being made for the scoop
Metal for the scoop all clamped together and left to set
Sealing tape going on the closing panel
Closing panel in
The two section all welded and lower section
Speakers all in
Front windscreen closing panel painted
Metal section being made for the scoop
Metal for the scoop all clamped together and left to set
Sealing tape going on the closing panel
Closing panel in
#54
Full Member
Thread Starter
Join Date: Nov 2011
Location: Ireland
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
Cheers Guys
Passenger side all bended and trial fitted
Front piece bent and cut out
Drivers view
All triall welded to hold in place
This arrived today 5 litre of resin and 5 meters of fiberglass
Passenger side all bended and trial fitted
Front piece bent and cut out
Drivers view
All triall welded to hold in place
This arrived today 5 litre of resin and 5 meters of fiberglass
#55
Full Member
Thread Starter
Join Date: Nov 2011
Location: Ireland
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
Lower section all welded in place
Front passenger side bracket made up and ready to be welded
Rear passenger side bracket
All welded in place
Drivers side rear bracket made up
Drivers side front bracket
Front passenger side bracket made up and ready to be welded
Rear passenger side bracket
All welded in place
Drivers side rear bracket made up
Drivers side front bracket
#56
Full Member
Thread Starter
Join Date: Nov 2011
Location: Ireland
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
Ok got the driver side floor plates all welded
Drivers rear floor plates all welded
This section took a good bit of marking,cutting all on my own as there was nobody around to help me its all welded up here
Front cross section all spot welded
Fully welded in
Drivers rear floor plates all welded
This section took a good bit of marking,cutting all on my own as there was nobody around to help me its all welded up here
Front cross section all spot welded
Fully welded in
#57
Hi Sean,
This is so odd, I've just got myself a FD, but I used to have a V6 MR2, and I remember following your thread on MR2OC, they gave you some hip on there I remember. I offered to re-trim your dash in Alcantara before I realised you were doing it in carbon fibre.
Amazing skill my friend, care to share how you managed to make a custom dash? I always thought about it for my MR2 but never followed through.
Steve
This is so odd, I've just got myself a FD, but I used to have a V6 MR2, and I remember following your thread on MR2OC, they gave you some hip on there I remember. I offered to re-trim your dash in Alcantara before I realised you were doing it in carbon fibre.
Amazing skill my friend, care to share how you managed to make a custom dash? I always thought about it for my MR2 but never followed through.
Steve
#60
Full Member
Thread Starter
Join Date: Nov 2011
Location: Ireland
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
@ Steve@edgeautomotive - Cheers for the offer on the re-trim on the dash i made the dash out of foam and carved the dash out of it to the shap i wanted then fiberglass the the mould then gel coat and skim bits of the dash with filler and then sent off for carbon fiber its an easy process but time consuming took me 3 months and over 500 hours to make
@ Scottish1 - Thanks its about 85% complete so its getting there
@ Cowboy BeeBop - Cheers
Last section to go in as there is nobody around to help me i had to improvise
Top section in place
Getting there
Any welded areas all sealed and any exposed areas all sealed
@ Scottish1 - Thanks its about 85% complete so its getting there
@ Cowboy BeeBop - Cheers
Last section to go in as there is nobody around to help me i had to improvise
Top section in place
Getting there
Any welded areas all sealed and any exposed areas all sealed
#65
Full Member
Thread Starter
Join Date: Nov 2011
Location: Ireland
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
@ RXM9600 - Cheers yip Ireland
Right have been under the weather with a cold not feeling the best got this done over the past few days
brackets for the roll cage
Drivers side bolted down well half bolted down only 14 more to go
Brackets all cut out and ground down
One side done only 3 more side to go
Drivers side finished
Roll cage all bolted down now all unts and bolts under sealed
Right have been under the weather with a cold not feeling the best got this done over the past few days
brackets for the roll cage
Drivers side bolted down well half bolted down only 14 more to go
Brackets all cut out and ground down
One side done only 3 more side to go
Drivers side finished
Roll cage all bolted down now all unts and bolts under sealed
#68
Full Member
Thread Starter
Join Date: Nov 2011
Location: Ireland
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
Have been doing a bit of work on a mr2 convertible so i got the chance to make up a frame for the door for a bit or strength as there is no weight in the doors and to stop them flexing when there opened
#71
Full Member
Thread Starter
Join Date: Nov 2011
Location: Ireland
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
Took this apart as it wouldnt fit in my booth a bit of work ahead
Cutting this out
Amp removed
Door metal surround all fiberglassed and sprayed up
Sub in position
Brackets all made
Amp in its box bit more work on this tomorrow
Cutting this out
Amp removed
Door metal surround all fiberglassed and sprayed up
Sub in position
Brackets all made
Amp in its box bit more work on this tomorrow
#72
Full Member
Thread Starter
Join Date: Nov 2011
Location: Ireland
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
Bass tunnel removed and drilled and re-tapped
All done
The amps new box
Booth all sound proofed with sound deading and sealed
More bars going in
Cross section
More modification as the gas ram was in the way nearly worked
Door up
All done
The amps new box
Booth all sound proofed with sound deading and sealed
More bars going in
Cross section
More modification as the gas ram was in the way nearly worked
Door up
#74
Full Member
Thread Starter
Join Date: Nov 2011
Location: Ireland
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
Drivers door to go all bolted as this is the only way to go
More rebar used and a bit of bending involved
Plate made up
Got two points welded before home time
More rebar used and a bit of bending involved
Plate made up
Got two points welded before home time