I would have to see quite a bit of interest. I currently do not have a RHD panel and I have to have an original to make the new one. I'll keep it in mind.

 

Is there an option for carbon fibre or carbon kevlar for the panels

 

Damn dave, nice work. I'd like one with the PFC integrated into it and some gauge panels. It'll be nice when everything is finished.

 

Actually I was planning on offering carbon kevlar or carbon fiber yes. The price will be higher on those.

 

i would suggest making a totally blank one except putting cut outs for the dimmer and the hazard...i would buy the arm rest one and the ac panel

 

If/When you make the shifter panels with the AC control units, please PM me? I have subscribed to this thread, but wouldnt mind a tap on the shoulder if its ready (a lot of projects fall thru on this board, at least the ones im interested in )

Highly interested in the shifter console with ac relocations! Just name yer price man!

Chris~

 

I'd be in if you offered the shifter panel with the a/c cutouts along with the blank a/c pannel

 

I will keep you all posted. Supplies to get me started were ordered a couple of days ago.

 

I'm interested in both Panels . . . how much should it be? $150? If so, you have a definate buyer.

EDIT: I have a Auto, there should be no issues with it fitting? Why would there be?

 

I am not offering a price on the second panel. I am not even sure I can make it from scratch yet. Let me get the ac panel done first then I will look into the center panel.

 

jsut a fyi the pic I posted the guy paid $900 sold them for $650 and I did one set and for the amount of work in them wont do anothe ac relocation custom dash for less than $450. I had plenty of intrest when I asked I people would be interested in getting them done for $350. Dont sell yurself short on the price.

 

Believe me if I custom make the set of both it will cost more than $150. Thanks for the good advice.

 

Oh yeah, i'd buy for more than $150; i'll keep track of this thread.

 

yeah definetely interested

 

interested. Good job so far!

 

Still interested, even if it is only the blank AC panel. Its not like mine works anyway

 

well then just to update, I did recieve the silicone supplies and I am working on the mold today and tomorrow.

 

Dave, i know you wouldn't do any work that wasn't up to par, but what is the thickness/strength of these panels compared to the stock plastic? also, would they have difficulty adhereing to paint if we decided to put a finish on them?

 

dave, haha i just noticed you and i are both rocking red squares i wonder if it's from the same guy? *cough*jim*cough*

- Charlie

 

Yea Charlie, Jim is about the only person i can think of who would waste time using those stupid things. Whatever floats yer boat i guess.
About the panel. I can dictate the thickness and I will keep it close to stock. I have not measured but it looks like 2 or 3mm. Painting should not be a problem.

 

Dave I tried to call you again last night but you were MIA.

And I'm also in the red square club b/c apparently that certain special someone wastes his time on me too.

 

Your square looks green to me. Try the shop number.

 

Dave,

Id be interested in the first design you posted about. Let me know if this takes off. I will have to come up and join you for a beer instead of shipping it.

Chris

 

Do you have any pics of how the shifter pannel is supposed to look so there isnt a lot of hammering on the tranny? Im redoing a shifter pannel for a local guy. BTW thanks for holding on to those black leather seats I bought from you for so long. I assumed my buddy was kepping you informed on when he was going to pick them up, he told me he would take care of it. Thanks agin Mike

 

Let me make that a little clearer, Pics of the shifter pannel after the ac relocation so there is not a ton of banging on the tranny tunnel. Thanks