**help me find this roof spoiler**
#1
A work in progress
Thread Starter
iTrader: (2)
Join Date: Aug 2010
Location: Miami
Posts: 262
Likes: 0
Received 0 Likes
on
0 Posts
**help me find this roof spoiler**
I came accross this roof spoiler. According to what I read it was offered as a dealer option... im not sure...
I looked around but no luck...
I looked around but no luck...
#3
A work in progress
Thread Starter
iTrader: (2)
Join Date: Aug 2010
Location: Miami
Posts: 262
Likes: 0
Received 0 Likes
on
0 Posts
Well one thing is comfirmed then... it was a factory option... now where can I get it ?
the roof spoiler from Shine is very different... is small compared to the one pictured...
the roof spoiler from Shine is very different... is small compared to the one pictured...
#5
I'm the Juggernaut BITCH!
iTrader: (7)
https://www.rx7club.com/showthread.p...6&highlight=fd
Last edited by RXtacy; 08-24-10 at 09:59 AM.
#6
A work in progress
Thread Starter
iTrader: (2)
Join Date: Aug 2010
Location: Miami
Posts: 262
Likes: 0
Received 0 Likes
on
0 Posts
they make the smaller one, but they also made a replica of that one. Pm ken and ask.
https://www.rx7club.com/showthread.p...6&highlight=fd
https://www.rx7club.com/showthread.p...6&highlight=fd
Trending Topics
#12
1262@54psi
iTrader: (7)
it comes with 2 mounting tabs and a bushing when u buy it at the dealer, so i used double sided tape to hold itto the top of the hatchand it uses a round rubber bushing in the center of the spoiler to keep it from sagging. so i had to make the bushing and use double sided tape to hold it in place.
#14
Built Not Bought
iTrader: (14)
Yeah, its just two strips of 3M tape. there are three holes around the edge. I'm only using the one in the center, It's a two inch long vacuum plug (you can get a pack of various sizes at autozone (to cap off un-needed vacuum sources on manifolds or wherever else), this is on the bottom of the spoiler, i then have a screw that goes through the top of the spoiler and into the rubber piece, this makes is so the wind can't push the back of the spoiler down and peel the tape up on the front edge.
I've never seen the brackets for the two holes on the sides.
I've never seen the brackets for the two holes on the sides.
#15
Been here since dirt...
Join Date: Jan 2009
Location: AZ
Posts: 327
Likes: 0
Received 0 Likes
on
0 Posts
Choose one tail spoiler OR the roof. Not both. Really ruins the lines. Looks JDM Ghetto.
If you do choose both, get spinners on your Dubs and some neon under the rockers.
gd
If you do choose both, get spinners on your Dubs and some neon under the rockers.
gd
#17
Full Member
iTrader: (4)
Join Date: Feb 2005
Location: tx/nj
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
hmmm guess now i gotta go buy some spinners and start calling my 7 dubs but iunno how imma gonna fit a small dodge under the 7 but i'll try.
edit: this is wat u mean right?
#19
A work in progress
Thread Starter
iTrader: (2)
Join Date: Aug 2010
Location: Miami
Posts: 262
Likes: 0
Received 0 Likes
on
0 Posts
Yeah, its just two strips of 3M tape. there are three holes around the edge. I'm only using the one in the center, It's a two inch long vacuum plug (you can get a pack of various sizes at autozone (to cap off un-needed vacuum sources on manifolds or wherever else), this is on the bottom of the spoiler, i then have a screw that goes through the top of the spoiler and into the rubber piece, this makes is so the wind can't push the back of the spoiler down and peel the tape up on the front edge.
I've never seen the brackets for the two holes on the sides.
I've never seen the brackets for the two holes on the sides.
#20
Built Not Bought
iTrader: (14)
you dont need to use the ones on the sides. Mine's been fine since April, you just need a rubber spacer in the middle hole so the spoiler doesnt flex downwards at speed and peel up the tape in the front.
you'll also notice the white car in the first post doesn't use them either.
you'll also notice the white car in the first post doesn't use them either.
Thread
Thread Starter
Forum
Replies
Last Post
risingsunroof82
1st Generation Specific (1979-1985)
8
09-07-15 01:11 PM