PINKSFC

, i was hoping u could help me with some base map set up on my FC. any advice or knowlege would be greatly appreciated.
the scoup: the cars a 89 fc it has haltech E11v2 u may have seen the car on pinks its the speed machine car its alson listed now in fc classifieds on this site. the thing is i need to do a remap on the haltech being that it is the new engine some tuning is required. the problem is that the ecu is locked with a password by dave gibson...who i cant contact....so i think i must start over. the car is equiped with gt45 turbo, 550cc primarys,1600cc. secondaries. street port and turbosmart bov. im looking for something semi streetable tune...nothing crazy anyt help would be great thanks!!!

Claudio RX-7

iTrader: (1)

As ive said before, just download the map that most closely resembles your setup, you can download more than one and mix and match.

Here is the most recent list.

https://www.rx7club.com/showpost.php...0&postcount=93

xUnKnOwNx

hi,

my car is sitting at theshop right now, i need to get it to driveable condition so i can drive it to steve kan to get it tuned in june. i tried the "E6X - Series 4/5 with 550/1600cc injectors and some mods." base map, except that i have 550/820cc injectors. i dont know how to tune this at all and neither does my shop. right now the car has some kind of hesitation at 2500 and at around 3000-3500 rpm, i hear detonation from my car. also my idle is jumping up and down from around 500-700. which base map would you recommend? or can you customize one for me?

1988 TII
street ported engine
racing beat 3" dp
bonez 3" hi flow cat
apexi n1 dual n1
stock 550cc primaries
siemans 820cc secondaries
walbro high pressure fuel pump
upgraded fuel rails, fpr
stock turbo, stock intake

black89rx7gtus

hey claudio i need a basemap made so i can put some mileage on mine so i can get it dynoed and run some boost. thanks man.
Mods are:
E6k
s5 13bt streetported
bnr stage 4
1600cc secondaries
720cc primaries
walbro 255lph
stock ignition including stock S5 tps
40psi fuel pressure with aeromotive fpr
right now running open 3in RB dp
ported TB
3bar map sensor

510

I have a stock ser.5 13bt running a haltech e6x if you have any maps that I could use would be very helpfull.....thanks

Viking War Hammer

iTrader: (8)

Hey dudes ! I need a Startup Map

TII Motor
Stock TII Ignition
(2) 1680cc primaries
(4) 1680 secondaries
3 Bar Map
GM TPS
GM AIT


If anyone has something like this, can you add 30% more fuel since I'll be starting it up on E85 ?

bwtp

you have a map for a
s4 TII stock motor
E6x
Stock ignition
720cc prim and secondaries
GM 3 bar Map sensor

sacabon

looking for a base with the following specs

13b-rew in a 93
haltech e6x
stock cas
3 bar map
stock tps
stock ignition coils
stock 850cc injectors all 4
single turbo

LEt me know thanks

mzrx7man

iTrader: (9)

I don't know why people are asking for maps when you can get one that is alittle close and modify it. No matter what map you get, your gonna have to alter it.

rx7goomba

Isnt this the "Post Haltech Base Map REQUESTS Here" thread? Hmm.....

mzrx7man

iTrader: (9)

hmmm... ok mr dee de dee lol... If it was a wierd setup then i would understand but something basically stock i know he's got something that would work.

foreveryonetosee

how about a base map for my s5 convertible
specs:
13b-rew none senquential
haltech e6x
stock ignitor and coils
stock injectors
no emissions
walbro 255lph
open 3' exhaust
2.5 bar map sensor (or whatever the e6x comes with)

let me know if you need anything else. pm with the results, thx

sacabon

If it's a stock setup then that's all I need to know. This project has been quite rough since most people seem to put this ecu in an fc and I'm using some stock fd sensors. No need to get like this. I'm just trying to eliminate some final issues and want to have a base map I can work with and if the main post has that base map already then a simple "here it is" reply would be nice. uhhg

mzrx7man

iTrader: (9)

Sorry i wasn't being an *** to you, i was just being a smart *** to the other guy.

1000hpRX7

i cant download the software for the base maps on e6x

Thedays

iTrader: (1)

Hi !!!

I search a good map for this setup.

Modification :
- Mazda rx7 1986 TII
- Premix
- Removed EGR Valve and all the other anti-pollution devices
- Haltech E6X
- Stock Primary Injectors
- 720CC Secondary Injectors
- S5 BNR Stage 2 Turbo
- FMIC
- Racing Beat Full exhaust system
- Innovate Wideband
- Blitz BOV

Thank you !!!

1000hpRX7

i am having a hard time viewing the maps how can i see them

1000hpRX7

cant view the base map for e6x with a stock motor, 3 bar map, stock injectors and coils. Is there any way someone can email it to me or something to where i can see it? bebes429@sbcglobal.net .Thanks

eo2am

iTrader: (9)

Can you use a fuel map from a e6x and use it on the e6k?

Using a 13b rew w/ 720/1680inj e6k

eo2am

iTrader: (9)

I guess this must of been a dumb question.

Anyone have a basemap for a e6k 720/1680

BDC

Need alot more information than that:

Injector setup
Engine setup and modifications
Fuel pump
Fuel pressure regulator (stock or adjustable aftermarket)
Turbocharger
Any other ignition hardware or otherwise changes

Email all of that to me at bdc@bdcmotorsports.com and I can cook something up for you. That goes for anyone else as well.

B

polito Racing

iTrader: (1)

hey guys I was just hoping someone has a basemap or could tell me where to find one to at least start my car. It is for an 87 S4 TII. Im running the stock CAS and coils, 720/1600 low impedance Injectors, haltech 3 bar MAP Sensor and a haltech E6S.

i dont know if this other info is needed but the other mods I have are
LC-1 Wideband
Greddy Profec B Boost Controller
Turbonetics T-66 Dual Ball Bearing
FMIC with 2.5" piping
3" free flow Dual exhaust (no cats)
walbro 255 fuel pump
all Emisions Removed
Large street port, SCR 2mm Apex seals,new bearings, side seals and all springs
(engine was just rebuilt and has 0 hours of run time.)
42mm Wastegate
9mm spark plug wires
Aeromotive a1000 FPR with all steel braided -6 hoses
ACT Max extreme clutch
ACT street lite flywheel
I also have 2 MSD 6Al's but they are not installed yet. I could be missing other modifications but i dont think it would matter anyway. please let me know if I missed to add any important info so I can go ahead and add it up.

thanks in advance

eff_three_see_es

iTrader: (11)

i was wondering if i could get a map made.

s5 turboII
haltech e6x
stock primarys and rc 550 secondays
fd fuel pump stock pressure
front mount ic
lightweight flywheel
aftermarket garrett turbo
tial 38mm wastegate
custom turbo manifold and downpipe
stock ignition

thanks in advance

otterball21

iTrader: (7)

Hey guys,

I am looking around and checked the post 93 also... I'm not too sure if the map would be close enough

I am running both 850cc injectors

I have an Haltech E6k

Rx6 Turbo
44mm wastegate
Motor is a 13B-rew
FMIC
Full 3 inch exhaust
AVC-R Boost controller

The 850cc's all the way around is what's throwing me off,
If anyone has a basemap they could send me or let me get off them..

Jack

boost_its_what_for_dinner

ill have my e6x soon and will need a base map for the following.
s4 t2 engine
large streetport
720/1600
fmic
aero. fpr
full 3" dp and exh.
gt35r with t4 exh. . 82
all emisions removed
walboro 255
stock ingition
46 mm wastegate
tubular mani. with 4" long screamer pipe
aem uego wb02
greddy pro fec type -s boost controller

thanks