Haltech Help ! My fine Feathered Friends ! **PICS**
Thread Starter
Joined: Jan 2007
Posts: 7,140
Likes: 0
From: Saint Louis / Illinois
Help ! My fine Feathered Friends ! **PICS**
Ripped my dash out last night, to make sure the Haltech Harness was in good condition and do some straightening up.................................oh and some WEIGHT REDUCTION. What a mess.
Anyhow, can someone tell me what these connectors are for. I pulled it from the engine bay, but forgot what they were hooked to.
I'm running an aftermarket intake and throttlebody so I'm even sure if I need them.
Yeah, a mess like I said. I hate trying to figure out other peoples wiring. And yes, these pictures are after I did lots of straightening.
Ok, this picture. I know the top connector go's to my 3 bar map sensor, middle is AIT sensor........ but I'm not sure what the last one go's to. It's NOT for the alternator.
Another one:
The connector on the left, with the greem rubber and one wire cut. What does that plug into ?
Okay, last one:
These two little connectors, what do they go to ?
Anyhow, can someone tell me what these connectors are for. I pulled it from the engine bay, but forgot what they were hooked to.
I'm running an aftermarket intake and throttlebody so I'm even sure if I need them.
Yeah, a mess like I said. I hate trying to figure out other peoples wiring. And yes, these pictures are after I did lots of straightening.
Ok, this picture. I know the top connector go's to my 3 bar map sensor, middle is AIT sensor........ but I'm not sure what the last one go's to. It's NOT for the alternator.
Another one:
The connector on the left, with the greem rubber and one wire cut. What does that plug into ?
Okay, last one:
These two little connectors, what do they go to ?
Thread Starter
Joined: Jan 2007
Posts: 7,140
Likes: 0
From: Saint Louis / Illinois
Thanks guys, can you quickly point me in the direction of that wiring diagram ?
Hopefully, I can get this done and wired up today. I want to fire this turd up !
Hopefully, I can get this done and wired up today. I want to fire this turd up !
Thread Starter
Joined: Jan 2007
Posts: 7,140
Likes: 0
From: Saint Louis / Illinois
Question
Wiring up my injectors now, Injector side of the harness only has 5 wires. Inj 1, 2, 3 and 4 and the digital Out 2. Does that sound right ?
Wiring up my injectors now, Injector side of the harness only has 5 wires. Inj 1, 2, 3 and 4 and the digital Out 2. Does that sound right ?
Last edited by Viking War Hammer; May 26, 2008 at 12:39 PM.
Trending Topics
There should be 4 coloured wires corresponding to each negative of each injector, and one +12v wire (red with green stripe?) The power gets daisy chained onto all 4 injectors. Polarity on the injectors doesn't matter. So yes, 5 wires in the injector harness sounds right.
Thread Starter
Joined: Jan 2007
Posts: 7,140
Likes: 0
From: Saint Louis / Illinois
Alright, I got the injectors wired up. Did I mention how much I hate electrical work.
It took me this long 9AM-3:45PM, just to get the injectors and Map Sensor hooked up.
It took me this long 9AM-3:45PM, just to get the injectors and Map Sensor hooked up.
Thread Starter
Joined: Jan 2007
Posts: 7,140
Likes: 0
From: Saint Louis / Illinois
From the same place I got the injectors, www.yourperformancesource.com
oh, still trying to get ahold of that guy with the template
oh, still trying to get ahold of that guy with the template
Thread
Thread Starter
Forum
Replies
Last Post
Devon300zx
2nd Generation Specific (1986-1992)
15
Sep 16, 2015 06:57 AM
Adaptronic Cranking fuel table messed up?
sherff
Adaptronic Engine Mgmt - AUS
5
Sep 12, 2015 12:22 PM
gabescanlon
3rd Generation Specific (1993-2002)
4
Sep 5, 2015 12:04 AM
