Haltech greddy boost sensor
greddy boost sensor
Hey, i was playing with this and i came across an issue with the Load Axis disappearing on you when you input the values for a custom sensor.
The fix is to input the values with the software in metric units, this means getting KPa units for the sensor you have, otherwise the Load axis on most of the 2D maps disappears on you (see pic), after you've input the values in KPa then you can revert to Imperial units and the Load Axis will display correctly. This issue was also present in v1.71.
Here are the calibrations for the Greddy 4bar MAP sensor both in PSI and KPa.
The fix is to input the values with the software in metric units, this means getting KPa units for the sensor you have, otherwise the Load axis on most of the 2D maps disappears on you (see pic), after you've input the values in KPa then you can revert to Imperial units and the Load Axis will display correctly. This issue was also present in v1.71.
Here are the calibrations for the Greddy 4bar MAP sensor both in PSI and KPa.
Last edited by Claudio RX-7; Sep 29, 2008 at 12:44 AM.
'Tuna'
Joined: Feb 2001
Posts: 4,637
Likes: 3
From: Miami,Fl,USA
Hey, i was playing with this and i came across an issue with the Load Axis disappearing on you when you input the values for a custom sensor.
The fix is to input the values with the software in metric units, this means getting KPa units for the sensor you have, otherwise the Load axis on most of the 2D maps disappears on you (see pic), after you've input the values in KPa then you can revert to Imperial units and the Load Axis will display correctly. This issue was also present in v1.71.
Here are the calibrations for the Greddy 4bar MAP sensor both in PSI and KPa.
The fix is to input the values with the software in metric units, this means getting KPa units for the sensor you have, otherwise the Load axis on most of the 2D maps disappears on you (see pic), after you've input the values in KPa then you can revert to Imperial units and the Load Axis will display correctly. This issue was also present in v1.71.
Here are the calibrations for the Greddy 4bar MAP sensor both in PSI and KPa.
This might help you with that problem----> https://www.rx7club.com/haltech-forum-62/reasons-weird-behaviour-your-e8-e11-firmware-update-issues-790256/
Seriously I have not had that problem with the latest revision on any of the applictions that I've done as of late especially since they all got custom map sensors and calibrations also.
Last edited by crispeed; Sep 29, 2008 at 06:11 PM.
Thread Starter
FC3S SENPAI
Joined: Jul 2007
Posts: 41
Likes: 0
From: Surprise,AZ
Hey, i was playing with this and i came across an issue with the Load Axis disappearing on you when you input the values for a custom sensor.
The fix is to input the values with the software in metric units, this means getting KPa units for the sensor you have, otherwise the Load axis on most of the 2D maps disappears on you (see pic), after you've input the values in KPa then you can revert to Imperial units and the Load Axis will display correctly. This issue was also present in v1.71.
Here are the calibrations for the Greddy 4bar MAP sensor both in PSI and KPa.
The fix is to input the values with the software in metric units, this means getting KPa units for the sensor you have, otherwise the Load axis on most of the 2D maps disappears on you (see pic), after you've input the values in KPa then you can revert to Imperial units and the Load Axis will display correctly. This issue was also present in v1.71.
Here are the calibrations for the Greddy 4bar MAP sensor both in PSI and KPa.
Thread
Thread Starter
Forum
Replies
Last Post