General Rotary Tech Support Use this forum for tech questions not specific to a certain model year
Sponsored by:
Sponsored by: CARiD

bad winding sound like a supercharger

Thread Tools
 
Search this Thread
 
Old Oct 23, 2013 | 11:00 PM
  #1  
joegallo13b's Avatar
Thread Starter
Full Member
 
Joined: Dec 2010
Posts: 105
Likes: 0
From: armonk ny
NY bad winding sound like a supercharger

Need help with my clean 87 s4 NA gxl. Its making a sound, like supercharger, winding when idling and around 4-6k rpm. When i push the clutch in, it goes away, im thinking its either the old clutch with, 80k miles on it, or the transmission. idk is it normal for a clutch to make that sound when they ware out? Because i do need a new clutch.
thanks for the help
Reply
Old Oct 23, 2013 | 11:02 PM
  #2  
joegallo13b's Avatar
Thread Starter
Full Member
 
Joined: Dec 2010
Posts: 105
Likes: 0
From: armonk ny
basically like the winding sound some alternators make when they go bad. I hope its not the engine like the side rotor housing.
Reply
Old Oct 23, 2013 | 11:09 PM
  #3  
joegallo13b's Avatar
Thread Starter
Full Member
 
Joined: Dec 2010
Posts: 105
Likes: 0
From: armonk ny
my friend says its the throw out bearing
Reply
Old Oct 24, 2013 | 12:20 PM
  #4  
10thaniv's Avatar
Life Project.
Tenured Member 15 Years
iTrader: (1)
 
Joined: Jan 2005
Posts: 605
Likes: 1
From: BEDFORD, TX
yep.
Reply
Old Oct 24, 2013 | 04:06 PM
  #5  
FelixIsGod29X's Avatar
Manual Rack
Tenured Member: 20 Years
iTrader: (50)
 
Joined: Aug 2005
Posts: 3,652
Likes: 1
From: Wanaque NJ
+1 to throw out bearing too.
Reply
Old Oct 25, 2013 | 06:31 PM
  #6  
joegallo13b's Avatar
Thread Starter
Full Member
 
Joined: Dec 2010
Posts: 105
Likes: 0
From: armonk ny
well guess what. It was leaking tranny fluid bad for a few days, from the broken rear main seal between the drive shaft and tranny. so its at the shop now getting that replaced. and if it still makes that sound after i will have to replace the clutch. Also is there a input shaft shaft bearing?

the clutch components are, pilot bearing-, flywheel-, clutch disc-, clutch pressure plate-, throw out bearing-, clutch release fork-, and input shaft bearing. anything else like bushings?
Reply
Old Oct 25, 2013 | 06:31 PM
  #7  
joegallo13b's Avatar
Thread Starter
Full Member
 
Joined: Dec 2010
Posts: 105
Likes: 0
From: armonk ny
is changing the clutch an easy job with basic tools and a friend to help?
Reply
Old Oct 25, 2013 | 06:48 PM
  #8  
invinciblejets's Avatar
Grabba Dabba Goo!
 
Joined: May 2013
Posts: 317
Likes: 0
From: murrells inlet sc
Originally Posted by joegallo13b
well guess what. It was leaking tranny fluid bad for a few days, from the broken rear main seal between the drive shaft and tranny. so its at the shop now getting that replaced. and if it still makes that sound after i will have to replace the clutch. Also is there a input shaft shaft bearing?

the clutch components are, pilot bearing-, flywheel-, clutch disc-, clutch pressure plate-, throw out bearing-, clutch release fork-, and input shaft bearing. anything else like bushings?
The input shaft bearing Is a transmission component... most likely is throw out bearing start with a full clutch kit (clutch, throw out bearing, pressure plate and pilot bearing) before you worry about input shaft bearing you can go awhile with one of those screaming....
Reply
Old Oct 25, 2013 | 07:06 PM
  #9  
joegallo13b's Avatar
Thread Starter
Full Member
 
Joined: Dec 2010
Posts: 105
Likes: 0
From: armonk ny
will do, thanks for the help
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Jeff20B
1st Generation Specific (1979-1985)
73
Sep 16, 2018 07:16 PM
The1Sun
1st Generation Specific (1979-1985)
7
Sep 18, 2015 07:13 PM
The1Sun
New Member RX-7 Technical
5
Sep 15, 2015 04:45 PM
The1Sun
1st Generation Specific (1979-1985)
0
Sep 7, 2015 10:21 PM
83revival
New Member RX-7 Technical
4
Sep 3, 2015 10:42 PM




All times are GMT -5. The time now is 06:51 PM.