anyone know how to wire up 2 MSD's to the trailings(FC)?
#1
Retired Moderator, RIP
Thread Starter
iTrader: (142)
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes
on
114 Posts
anyone know how to wire up 2 MSD's to the trailings(FC)?
I got 3 MSD 6a's and I know the boxes are just IN and out..
I need info on how to wire the trailing coils with one box per plug.
So 1 box to leading and 2 for trailings.
On a 88 S4 N/A.
..anyone got any info,wire colors..etc
Thanks..STYX!~
(don't ask why I am doing it.I just am..because I can!)
I need info on how to wire the trailing coils with one box per plug.
So 1 box to leading and 2 for trailings.
On a 88 S4 N/A.
..anyone got any info,wire colors..etc
Thanks..STYX!~
(don't ask why I am doing it.I just am..because I can!)
#4
Moderator
iTrader: (3)
Cooter? who gives a tiger's tit where Cooter is ... i'm lookin' for Daaai-zeh!
but seriously, I tried searching around and it seems the only thing people post about is wiring it to the leading coil. I guess it makes sense though.
at any rate, i'll see if I can dig up my schematic of the trailing coil and my old wiring diagram for my 6AL. it shouldn't be too hard to figure out. my guess is it will go something like wiring the boxes to the coils per usual and using the coil select (I forget which color wire) to trigger them.
oh, and even if I fail to find my MSD diagrams (it's been about 20 years ), i'm pretty sure I saw a generic MSD 6A schematic on Ted's site (FC3 Pro or something like that).
but seriously, I tried searching around and it seems the only thing people post about is wiring it to the leading coil. I guess it makes sense though.
at any rate, i'll see if I can dig up my schematic of the trailing coil and my old wiring diagram for my 6AL. it shouldn't be too hard to figure out. my guess is it will go something like wiring the boxes to the coils per usual and using the coil select (I forget which color wire) to trigger them.
oh, and even if I fail to find my MSD diagrams (it's been about 20 years ), i'm pretty sure I saw a generic MSD 6A schematic on Ted's site (FC3 Pro or something like that).
#6
Moderator
iTrader: (3)
the trailing coil wiring:
black = tach signal (?)
yellow = IGF (?)
gray = (?) - [i'll have to double check this to see if I can figure it out]
white = coil select
red = IGT (trigger)
beige (tan) = +12v switch
beige (tan) = +12v switch
blue = T2 ground
________________________________________
the MSD 6A
FC3S Pro v2.0:  HOW-TO - CDI (MSD/Crane) Installation
black = tach signal (?)
yellow = IGF (?)
gray = (?) - [i'll have to double check this to see if I can figure it out]
white = coil select
red = IGT (trigger)
beige (tan) = +12v switch
beige (tan) = +12v switch
blue = T2 ground
________________________________________
the MSD 6A
FC3S Pro v2.0:  HOW-TO - CDI (MSD/Crane) Installation
#7
Retired Moderator, RIP
Thread Starter
iTrader: (142)
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes
on
114 Posts
Well I shouldn't need the trigger...only just separate the boxes and coils To individually get Power into the box from the harness and then out to the coils.
ah..I'll take a peek while I am painting.
ah..I'll take a peek while I am painting.
Thread
Thread Starter
Forum
Replies
Last Post
toplessFC3Sman
2nd Generation Specific (1986-1992)
6
03-20-18 01:54 PM
HalifaxFD
Canadian Forum
126
05-09-16 07:06 PM