RX7Club.com - Mazda RX7 Forum
And here's a shot with the belt guide installed as a test fit
And here's a shot with the belt guide installed as a test fit
0 2023/02/19 12:58:08
0 2023/02/19 12:58:02
This is how you would use these in the car - undo one snap, thread the shoulder belt & re-snap the guide back on
This is how you would use these in the car - undo one snap, thread the shoulder belt & re-snap the guide back on
0 2023/02/19 12:57:57
And here's the leather guide version - I purchased the leather online, and the color match wasn't as good in real life. Might do a version 3 using the leather from my old seats to get a better match, as the leather is much sturdier than the fabric
And here's the leather guide version - I purchased the leather online, and the color match wasn't as good in real life. Might do a version 3 using the leather from my old seats to get a better match, as the leather is much sturdier than the fabric
0 2023/02/19 12:57:53
And here it is installed in the car, Fabric belt guide version
And here it is installed in the car, Fabric belt guide version
0 2023/02/19 12:57:47
0 2023/02/19 12:37:18
And here's what they look like unpacked on my living room floor. Three pieces for each seat - a bottom cushion section, the seat back/headrest section and the center/lumbar section of the seat back.
And here's what they look like unpacked on my living room floor. Three pieces for each seat - a bottom cushion section, the seat back/headrest section and the center/lumbar section of the seat back.
0 2023/02/12 08:09:11
They were well packed & folded inside out and sealed in plastic
They were well packed & folded inside out and sealed in plastic
0 2023/02/12 08:08:10
0 2023/02/12 07:28:00
0 2023/02/12 07:27:42
0 2023/02/12 07:27:18
0 2023/01/29 12:15:30
0 2023/01/22 12:48:15
0 2023/01/22 12:48:13
0 2023/01/22 10:04:40
0 2023/01/15 03:46:32
More mock-up progress - here you can see how almost the entire cone top is open to flow air from the plenum, before I opened up part of the cone's side where the plenum mates over it.
More mock-up progress - here you can see how almost the entire cone top is open to flow air from the plenum, before I opened up part of the cone's side where the plenum mates over it.
0 2023/01/13 16:33:35
Mock up progress - here you can see the larger "snorkus" opening, and the new cone enclosure
Mock up progress - here you can see the larger "snorkus" opening, and the new cone enclosure
0 2023/01/13 16:33:30
Here's a view of the finished CAI where you can see the plenum (painted black) attached to the cone.
Here's a view of the finished CAI where you can see the plenum (painted black) attached to the cone.
0 2023/01/13 16:33:25
Finished view of the completed CAI V3 from the driver's side
Finished view of the completed CAI V3 from the driver's side
0 2023/01/13 16:33:18
Another engine bay view - if that CAI was made of black plastic, it would almost look OEM
Another engine bay view - if that CAI was made of black plastic, it would almost look OEM
0 2023/01/13 16:33:12
Bi-LED Low Beam test - Still need to adjust the aim here.
Bi-LED Low Beam test - Still need to adjust the aim here.
0 2023/01/13 16:12:49
Bi-LED High Beam test - Still need to adjust the aim here.
Bi-LED High Beam test - Still need to adjust the aim here.
0 2023/01/13 16:12:44
Completed Headlight housing & Bi-LED projector assembly ready for install in my FD
Completed Headlight housing & Bi-LED projector assembly ready for install in my FD
0 2023/01/13 16:12:38
^And another "after" data set, this time in 5th gear, lower RPMs & more throttle, attempting to induce some creep
^And another "after" data set, this time in 5th gear, lower RPMs & more throttle, attempting to induce some creep
0 2022/12/18 15:37:28
^Here's some "after" data, 3lb WG springs, 3rd gear pull
^Here's some "after" data, 3lb WG springs, 3rd gear pull
0 2022/12/18 15:37:27
^This is the "before" data, 3rd gear pull with the 7lb WG springs
^This is the "before" data, 3rd gear pull with the 7lb WG springs
0 2022/12/18 15:37:25
This is the 3rd gear pull
This is the 3rd gear pull
0 2022/12/14 12:32:27
And here is a 5th gear pull, attempting to induce some creep.
And here is a 5th gear pull, attempting to induce some creep.
0 2022/12/14 12:32:26
0 2022/12/09 11:30:03
0 2022/11/29 16:19:14
0 2022/11/24 07:04:58
Finished Housing & Bi-LED Projector assemblies
Finished Housing & Bi-LED Projector assemblies
0 2022/11/23 08:28:05
0 2022/11/23 08:23:38
Installed in the housing with modified washers
Installed in the housing with modified washers
0 2022/11/23 08:12:41
The left is the unmodified H4 washer as-is; in the center is the H4 washer after grinding off the alignment key, and to the right is the other alignment washer I'm going to glue to the modified H4 washer to make it work!
The left is the unmodified H4 washer as-is; in the center is the H4 washer after grinding off the alignment key, and to the right is the other alignment washer I'm going to glue to the modified H4 washer to make it work!
0 2022/11/23 08:12:36
0 2022/11/23 08:12:30
And here you can see my new alignment washer, that consists of the modified H4 washer and the other alignment washer glued on top after testing alignment & marking up prior to gluing.
And here you can see my new alignment washer, that consists of the modified H4 washer and the other alignment washer glued on top after testing alignment & marking up prior to gluing.
0 2022/11/23 08:12:25
And here's the twisted beam pattern - it should be level & horizontal
And here's the twisted beam pattern - it should be level & horizontal
0 2022/11/23 08:12:19
Setting up to test beam alignment. I'm using the unmodified H4 washer as-is here, housing is sitting level on a surface as it would be when installed in the FD, and projecting against opposite wall in my basement.
Setting up to test beam alignment. I'm using the unmodified H4 washer as-is here, housing is sitting level on a surface as it would be when installed in the FD, and projecting against opposite wall in my basement.
0 2022/11/23 08:11:56