RX7Club.com - Mazda RX7 Forum
0 2016/12/23 21:41:37
Before
Before
0 2016/12/23 21:42:09
After. The rear can go lower once the inner guard lip has been rolled.
After. The rear can go lower once the inner guard lip has been rolled.
0 2016/12/23 21:42:42
Started making the sump. Used building paper as a template which wasn't the best idea.
Started making the sump. Used building paper as a template which wasn't the best idea.
0 2017/01/06 17:02:19
0 2017/01/06 17:03:45
0 2017/01/06 17:04:15
0 2017/01/06 17:04:42
A few of the holes required a bit of massaging, but overall turned out good. Still need to machine out baffles and oil pick up points.
A few of the holes required a bit of massaging, but overall turned out good. Still need to machine out baffles and oil pick up points.
0 2017/01/06 17:06:11
The engine bay of the rx7. Its a 1986 FC. Extend port, garrett gt3582r. 360rwhp. First rotary i have built, 20000kms later still going hard.
The engine bay of the rx7. Its a 1986 FC. Extend port, garrett gt3582r. 360rwhp. First rotary i have built, 20000kms later still going hard.
0 2017/01/06 17:09:12
0 2017/01/06 17:13:36
Finished the final shape of the sump
Finished the final shape of the sump
0 2017/01/21 18:49:33
0 2017/01/21 18:50:41
Started to make a bracket for the alternator and oil pump
Started to make a bracket for the alternator and oil pump
0 2017/01/21 18:51:28
0 2017/01/21 18:52:32
0 2017/01/21 18:52:53
Ended up with a giant swarf pile.
Ended up with a giant swarf pile.
0 2017/01/21 18:53:19
0 2017/01/21 22:05:34
Start of the engine mounts. Will bolt straight to the foward subframe mounts.
Start of the engine mounts. Will bolt straight to the foward subframe mounts.
0 2017/01/27 13:11:28
Bending the engine mounts, bender is bolted to the forks on the forklift.
Bending the engine mounts, bender is bolted to the forks on the forklift.
0 2017/02/03 17:47:36
0 2017/02/03 17:48:45
0 2017/02/03 17:49:07
0 2017/02/03 17:49:28
0 2017/02/09 21:15:00
0 2017/02/09 21:15:31
0 2017/02/09 21:15:57
0 2017/02/09 21:16:22
0 2017/02/09 21:16:43
Photo doesn't show it very well, but the adapter is bored out to fit snugly on this shaft.
Photo doesn't show it very well, but the adapter is bored out to fit snugly on this shaft.
0 2017/02/15 21:30:43
Bush, this is a press fit into the bellhousing.
Bush, this is a press fit into the bellhousing.
0 2017/02/15 21:33:37
I machined a few mm out of the bore on the bellhousing to get a bit more material thickness on the bush.
I machined a few mm out of the bore on the bellhousing to get a bit more material thickness on the bush.
0 2017/02/15 21:34:48
Made a pushrod for the alternator belt tension adjustment.
Made a pushrod for the alternator belt tension adjustment.
0 2017/02/17 21:17:31
0 2017/02/17 21:18:43
0 2017/02/17 21:19:49
0 2017/02/18 19:01:47
0 2017/02/18 19:02:20
0 2017/02/18 19:03:06
0 2017/02/18 19:03:27
0 2017/02/19 16:28:29
0 2017/02/19 16:28:59
0 2017/02/19 16:29:42