RX7Club.com - Mazda RX7 Forum
0 2016/12/08 19:42:53
0 2016/12/08 19:43:17
Its nice working with brand new parts.
Its nice working with brand new parts.
0 2016/12/08 19:43:41
All seals fitted, ready for assembly.
All seals fitted, ready for assembly.
0 2016/12/08 19:44:34
View of the stationary gear mod
View of the stationary gear mod
0 2016/12/10 13:47:19
#1 rotor
#1 rotor
0 2016/12/10 13:48:18
0 2016/12/10 13:49:06
0 2016/12/10 13:49:44
Thought getting this center plate on would be a bit tricky, but it pretty much fell into place.
Thought getting this center plate on would be a bit tricky, but it pretty much fell into place.
0 2016/12/10 13:50:12
#3 rotor
#3 rotor
0 2016/12/10 13:52:13
0 2016/12/10 13:52:57
0 2016/12/10 13:53:28
#4 rotor
#4 rotor
0 2016/12/10 13:53:58
0 2016/12/10 13:54:36
A completed 4 rotor apart from front stack.
A completed 4 rotor apart from front stack.
0 2016/12/10 13:55:04
0 2016/12/13 01:03:13
Set the endplay, was able to use a spacer i had laying which was easy.
Set the endplay, was able to use a spacer i had laying which was easy.
0 2016/12/13 01:05:57
Gave cosmo #1 a wash and took it for a drive.
Gave cosmo #1 a wash and took it for a drive.
0 2016/12/13 01:08:21
0 2016/12/13 01:09:28
Gave Cosmo #1 a wash and took it for a drive
Gave Cosmo #1 a wash and took it for a drive
0 2016/12/13 01:12:12
0 2016/12/13 01:12:58
Gave Cosmo #1 a wash and took it for a drive
Gave Cosmo #1 a wash and took it for a drive
0 2016/12/13 01:16:19
0 2016/12/13 01:17:10
Front cover installed
Front cover installed
0 2016/12/15 18:40:26
0 2016/12/15 18:41:13
Using an Xtreme Rotaries ewp adapter with -20AN fittings, really nice part all cnc machined.
Using an Xtreme Rotaries ewp adapter with -20AN fittings, really nice part all cnc machined.
0 2016/12/15 18:41:34
0 2016/12/15 18:44:07
0 2016/12/15 18:44:34
Its really heavy, weighs about 33kgs.
Its really heavy, weighs about 33kgs.
0 2016/12/18 15:24:51
The plate is 1 inch thick which makes it difficult to cut on a band saw. I used a 64 tooth carbide tipped circular saw blade designed for aluminium. To make the 400mm cut above it only took about 3mins.
The plate is 1 inch thick which makes it difficult to cut on a band saw. I used a 64 tooth carbide tipped circular saw blade designed for aluminium. To make the 400mm cut above it only took about 3mins.
0 2016/12/18 15:25:54
Getting the plate to thickness for trans adapter
Getting the plate to thickness for trans adapter
0 2016/12/18 15:31:26
0 2016/12/18 15:32:42
0 2016/12/18 15:33:14
Cut a chunk off the transmission flange.
Cut a chunk off the transmission flange.
0 2016/12/18 15:37:05
Starter motor now fits
Starter motor now fits
0 2016/12/18 15:38:17
Swarf everywhere
Swarf everywhere
0 2016/12/18 15:38:57
Test fit
Test fit
0 2016/12/18 15:40:32
0 2016/12/18 15:41:06
Finished adapter
Finished adapter
0 2016/12/18 15:41:34
Towed the car out of the tent with the mighty Honda.
Towed the car out of the tent with the mighty Honda.
0 2016/12/23 21:39:59