RX7Club.com - Mazda RX7 Forum
0 2026/02/01 12:06:48
0 2026/02/01 12:06:51
0 2026/02/01 12:06:54
0 2026/02/01 12:06:57
0 2026/02/01 12:07:01
0 2026/02/01 12:07:04
0 2026/02/01 12:07:08
0 2026/02/01 12:07:11
0 2026/02/01 13:06:46
0 2026/02/01 13:06:49
0 2026/02/01 13:06:54
0 2026/02/01 13:06:56
0 2026/02/01 13:06:58
0 2026/02/01 13:07:00
0 2026/02/01 13:07:02
0 2026/02/01 13:07:03
0 2026/02/01 13:07:06
0 2026/02/01 13:07:10
0 2026/02/01 13:07:14
0 2026/02/01 13:07:17
0 2026/02/01 13:07:19
0 2026/03/20 00:14:11
0 2026/03/20 00:14:19
0 2026/03/20 00:14:23
0 2026/03/20 00:14:31
Power steering All components have been degreased, wire brushed, primered and painted. All fasteners have been refinished in black nickel or nickel sulfamate
Power steering All components have been degreased, wire brushed, primered and painted. All fasteners have been refinished in black nickel or nickel sulfamate
0 2026/03/20 00:19:15
Original a/c components cleaned up and looking new.
Original a/c components cleaned up and looking new.
0 2026/03/20 00:19:55
Radiator fans were replaced with new dual flex-a-lite s-type fans. New mishimoto radiator with all new coolant lines throughout the engine bay.
Radiator fans were replaced with new dual flex-a-lite s-type fans. New mishimoto radiator with all new coolant lines throughout the engine bay.
0 2026/03/20 00:21:01
Radium engineering fuel components throughout.
Radium engineering fuel components throughout.
0 2026/03/20 00:21:45
All ready to go in
All ready to go in
0 2026/03/21 10:52:54
0 2026/03/21 10:52:56
Tool a little bit to creep the motor in. Luckily I had a hoist and engine jack. When I decided to do this I had no one to assist so installed it myself. Was a lot easier than I thought it would be
Tool a little bit to creep the motor in. Luckily I had a hoist and engine jack. When I decided to do this I had no one to assist so installed it myself. Was a lot easier than I thought it would be
0 2026/03/21 10:53:18
I replaced the factory master cylinder with a new 929 master. I did not use the original fluid reservoir with a clutch fluid feed so I’ve installed a willwood reservoir
I replaced the factory master cylinder with a new 929 master. I did not use the original fluid reservoir with a clutch fluid feed so I’ve installed a willwood reservoir
0 2026/03/21 10:53:55
All lines, brackets and fasteners have been refinished or replaced with new oem parts. New hoses and seals throughout
All lines, brackets and fasteners have been refinished or replaced with new oem parts. New hoses and seals throughout
0 2026/03/21 10:54:25
A/c system all components restored
A/c system all components restored
0 2026/03/21 10:54:45
Cooling system in. Mishimoto radiator. I kept the oem fan shroud but replaced the original 2 speed fans with 2 12” single speed flex-a-lite fans.
Cooling system in. Mishimoto radiator. I kept the oem fan shroud but replaced the original 2 speed fans with 2 12” single speed flex-a-lite fans.
0 2026/03/21 10:55:35
Fuel system. Radium engineering components throughout. 6AN fittings and lines. Perrin fuel pressure regulator
Fuel system. Radium engineering components throughout. 6AN fittings and lines. Perrin fuel pressure regulator
0 2026/03/21 10:56:28
0 2026/03/24 00:35:03
Took a lot less time than I thought it would. Luckily I had a hoist and engine jack to get the job done quick
Took a lot less time than I thought it would. Luckily I had a hoist and engine jack to get the job done quick
0 2026/03/24 00:35:06
Lookin good with some goodies mounted.
Lookin good with some goodies mounted.
0 2026/03/24 00:35:09