Offical if you must post pics of your FC3S in the 2nd gen section
#1
Offical if you must post pics of your FC3S in the 2nd gen section
moderators note: This thread is compiled and merged from multiple threads all showing pictures of owners 2nd generation RX-7s)
If you have questions or comments about the pictures posted in this thread, please PM or email the forum member instead of posting in this thread. This thread should be just for pictures
This thread is currently being edited by the moderators to remove the existing comments and questions.
Thanks to Aaron Cake hosting them.
88GXL>89TII Engine/Drivetrain
If you have questions or comments about the pictures posted in this thread, please PM or email the forum member instead of posting in this thread. This thread should be just for pictures
This thread is currently being edited by the moderators to remove the existing comments and questions.
Thanks to Aaron Cake hosting them.
88GXL>89TII Engine/Drivetrain
Last edited by Icemark; 03-31-06 at 11:04 AM.
Trending Topics
#9
Yes, I have plans for a T04B divided. It was to have gone on this Spring but previous rebuild went bad due to 100% the rebuilder.
East Bear's Is what I have on. I got them from the rx7store.net. In stock form the lighting provided Is rather poor. I have since upgraded the bulbs to H3 PIAA Xtreme Whites.
I am not sure If these pics can be had In higher resolution. I found a few shots of my seats, although vague.
Random shot
East Bear's Is what I have on. I got them from the rx7store.net. In stock form the lighting provided Is rather poor. I have since upgraded the bulbs to H3 PIAA Xtreme Whites.
I am not sure If these pics can be had In higher resolution. I found a few shots of my seats, although vague.
Random shot
#10
spending too much money..
iTrader: (2)
well what do you guys think of my project now (pics)
here it is my project of a couple of years finally done to the point at least I can drive it around. Need to get it tuned soon but for now it will do. Here are a few pics I know some won't like it because it's got racing stripes but thats ok so far I love this thing Threw blood sweat and tears...
#14
man I bet it felt good to finish it after that much time and work.
My car has been down for longer than that. If I can keep my focus
I should be able to finish it very soon.
My car has been down for longer than that. If I can keep my focus
I should be able to finish it very soon.
#16
Senior Member
Join Date: Jul 2002
Location: Mt. Pleasant, MI
Posts: 291
Likes: 0
Received 0 Likes
on
0 Posts
Love the wing!!!
I actually have the same wing and I love it. It is actually lower than most people think (see pic). It is lower than the roofline and it is a wing made by Wings West (Super 7 spoiler PN 581134).
What is most important, is that you like it.
Thanx
Michael
What is most important, is that you like it.
Thanx
Michael
#22
Full Member
Join Date: Aug 2002
Location: Baton Rouge, La.
Posts: 203
Likes: 0
Received 0 Likes
on
0 Posts
#23
Locust of the apocalypse
Join Date: Apr 2003
Location: Directly above the center of the earth (York, PA)
Posts: 2,553
Likes: 0
Received 1 Like
on
1 Post
Originally Posted by vice
hey years of decay: what did you use to polish your UIM?
that picture actually sucks..... but.. lets see here... first i use a die grinder and take all the casting marks out, then we start with 80 grit sand paper... working up to 600..
I use a motor with a flex shast and sandpaper cones in 80 120 and 220 to get into the nooks
Then I use a felt bob on the flex shaft in the nooks with cut and color compund from Caswell....
Then I hit the whole thing with CutNColor on a Sisal Wheel on the Buffing machine
Then I hit it with CutNColor on a Sewn Cotton Wheel on the buffer
and finally, high color compouind and a loose flannel wheel.
Check it out:
BTW this is zkellers intake pictured above... He's the other Retard in TRB Polishing
Last edited by YearsOfDecay; 11-24-04 at 12:27 AM.