Unreal PR

iTrader: (2)

Like the title says, I'm looking for a wiring diagram for a 96 FD. Specifically, the engine. If you have any more Series 7 or 8 wiring diagrams that you are willing to share, I'll be happy to get a copy. I figured I would ask you guys before going to the 3rd gen section. Even with the search function I couldn't get anything.

Unreal PR

iTrader: (2)

Even an ecu pinout of a 96 and 89 could help.

galvatron10000

iTrader: (4)

did you ask the Australians? they deal with RHD;. i know there a manual you can download, but it is in katakana, but if you have a katakana translator or speak nippon ( i would assume you would since your location is Japan), you can see that the words are english but with a touch of nippon.

Unreal PR

iTrader: (2)

I posted on ausrotary today, so it's a matter of waiting. If you know where I can download or view the manual, I would greatly appreciate it. I can read katakana and hiragana. It's just a matter of translating the hiragana. Katakana is easy to translate. Thank you for that information, anything helps.

P.S. I like how you said "the Australians". I read it like it was forbidden to talk about them. Haha.

galvatron10000

iTrader: (4)

they are from Australia. lol. anyway i'm still looking for it, but i'm positive i saw a pdf of one before. i'll post it if i find it. but i have a JDM and its pretty much the same thing. i don't have ODB II, but i don't think its much different

Unreal PR

iTrader: (2)

I saw a thread once from like 2005 with a link on a random download website. It wasn't working by the time I got to it. If you do find it, I would be so happy to have it. I'll need it to wire my S5 engine harness to run a 96 engine on a 93-95 Power FC in my FC3S. Weird, isn't it? Lots of work. :/

GodSquadMandrake

You just need to search in Japanese on google and you'll find it. The wiring diagram is in katakana mostly.

Unreal PR

iTrader: (2)

I've searched a little bit and found a 93-95 ecu pinout and even a fc dedicated website(awesome) but nothing much else. I'll keep looking though, since that actually produced better results.

R-R-Rx7

iTrader: (24)

here you go

Unreal PR

iTrader: (2)

Dude, you are a badass. If you need anything, I'll do my best to help!

R-R-Rx7

iTrader: (24)

Not a problem. Glad to help

cr-rex

iTrader: (114)

What is that a pinout of and for?

Unreal PR

iTrader: (2)

96 JDM FD ECU. I need it so i can trace wires and alter the harness alittle.

cr-rex

iTrader: (114)

Oh. I see now. I didnt understand the diagram of the plugs. Theyre stacked on top of each other. My bad. What are the blacked out plugs supposed to be?

Unreal PR

iTrader: (2)

They're stacked because 96+ is 16bit ECU as opposed to the 8bit used in 93-95 fd and fc's. The blacked out part on top is showing you what the back of the ECU would look like if you were to see it like the harness was going in.

R-R-Rx7

iTrader: (24)

the blackened ones = NOT USED

out of the 4 plugs you can see there only the three are actual plugs

freaknbigpanda

Do you guys know which of these wires in that diagram I would have to cut to disable the speed limiter on my FD? I have a 1996 JDM fd.

Circuit Theory

iTrader: (52)

Im pretty sure it is more complicated than just cutting a single wire. I know the spped limiter is removed with a rom tune, or you could swap your computer for a computer from a country or state that does not have speed limiters. What speed MPH or KMPH does it cut at?

freaknbigpanda

it cuts at 180km/h as per japanese spec... there is a thread in the 3rd gen board that says you can cut a wire to get around the speed limiter, this is the one I am talking about:

https://www.rx7club.com/3rd-generati...-668599/page2/

if you check out the last post on that page the guy says it works for the 16bit ecu