Project D1's Project. . .lulz. . .
#76
Full Member
Thread Starter
iTrader: (2)
Join Date: Mar 2004
Location: Canada
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
If anyone is looking for USDM interior parts, lemme know. . .most of it is in excellent condition. . .black as well. . .
Finally got it pulled out of storage and into the shop, started stripping interior down and prepping for a cage. . .
mocked up the wheels and the kit. . .need to go a little wider or run some spacers. . .
Need to figure out some sort of paint scheme. . .or it's just going two tone black and white. . .
Finally got it pulled out of storage and into the shop, started stripping interior down and prepping for a cage. . .
mocked up the wheels and the kit. . .need to go a little wider or run some spacers. . .
Need to figure out some sort of paint scheme. . .or it's just going two tone black and white. . .
#77
Failcopter..it's here..
iTrader: (6)
Join Date: Aug 2008
Location: near phoenix....kinda...
Posts: 721
Likes: 0
Received 1 Like
on
1 Post
i need black door panels and roof(sun roof....) but im sure its gonna be super stupid expensive to ship lol. You also said u had different wheels and sizes. what else u got .............?? lol
#78
Full Member
Thread Starter
iTrader: (2)
Join Date: Mar 2004
Location: Canada
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
18x13 -20 rear
18x10.5 -1 front
Looking into some BFG's in 335's and 275's for the front. . .
#85
Full Member
Thread Starter
iTrader: (2)
Join Date: Mar 2004
Location: Canada
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
Engine is assembled for the most part. . .did a little porting today on the UIM and prepping for the LIM. . .
Fat street port, RA Super Seals, race bearings. . .
Bought this before I did any research on it, have read mixed reviews about it but I'll try it out. . .Rotary Works 90mm TB. . .hope it performs as well as it looks. . .
Not much point to this throttle body if you keep the secondary butterflies. . .bottleneck much?
Removed the butterflies. . .scratched the outline of where the TB sits on the UIM. . .
Removed the bridge, going to clean it up tomorrow. . .
Xcessive Engineering LIM. . .going to port match this tomorrow as well. . .
Clutch is installed . . .ready to mate up transmission tomorrow. . .
Fat street port, RA Super Seals, race bearings. . .
Bought this before I did any research on it, have read mixed reviews about it but I'll try it out. . .Rotary Works 90mm TB. . .hope it performs as well as it looks. . .
Not much point to this throttle body if you keep the secondary butterflies. . .bottleneck much?
Removed the butterflies. . .scratched the outline of where the TB sits on the UIM. . .
Removed the bridge, going to clean it up tomorrow. . .
Xcessive Engineering LIM. . .going to port match this tomorrow as well. . .
Clutch is installed . . .ready to mate up transmission tomorrow. . .
#86
Original Gangster/Rotary!
iTrader: (213)
Those rules are in place to prevent people from being robbed by scammers, back in the day it happened all too frequently.... I'm not talking 10 bucks either.
Any pics of your portwork? Also, more details on your race bearings?
thanks
#89
Full Member
Thread Starter
iTrader: (2)
Join Date: Mar 2004
Location: Canada
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
Reason for a new engine is a friend blew his up right before a roadtrip he wanted to do for a while, so I sold him mine. . .
#90
Full Member
Thread Starter
iTrader: (2)
Join Date: Mar 2004
Location: Canada
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
Probably because you didn't read the rules so your thread was deleted.
Those rules are in place to prevent people from being robbed by scammers, back in the day it happened all too frequently.... I'm not talking 10 bucks either.
Any pics of your portwork? Also, more details on your race bearings?
thanks
Those rules are in place to prevent people from being robbed by scammers, back in the day it happened all too frequently.... I'm not talking 10 bucks either.
Any pics of your portwork? Also, more details on your race bearings?
thanks
Ah k, good to know. . .
I'll have some more detailed pics of the ports later on today. . .and I believe the bearings are Mazdaspeed's race bearings, I'll clarify this later as well. . .
#91
Original Gangster/Rotary!
iTrader: (213)
Based on the pics they're regular ol' FD bearings. You don't want to run MFR (mazda factory race) bearings on a street car that sees low rpm use, they're meant for full-blown race cars that operate constantly near redline.
#92
Senior Member
iTrader: (5)
Join Date: Jan 2002
Location: edmonton alberta
Posts: 345
Likes: 0
Received 0 Likes
on
0 Posts
The bearings are, rotor bearings 4801-11-111 mazda race bearings. 0.04" deeper oil groove. The mains are factory bearings that have "correct" clearances as 8 different ones are avail. It's a picture. I wouldn't expect you to be able to measure them from a pic, maybe you shouldn't criticize what you don't know.
#93
Full Member
Thread Starter
iTrader: (2)
Join Date: Mar 2004
Location: Canada
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
So from this. . .
To this. . .
At the moment. . .Going to fill some ports, knife edge and clean it up. . .
4 port fuel rail goodness. . .going with 6 1000cc ID injectors. . .
Just make sure your manifold/turbo will fit with this setup. . .this LIM moves the UIM forward a few cm's. . .mine just fits. . .
Twin oil cooler kit. . .very cool. . .thanks SB Garage!
Started on the fuel system, will get the accessories on and hopefully get to the piping and ducting later today. . .
To this. . .
At the moment. . .Going to fill some ports, knife edge and clean it up. . .
4 port fuel rail goodness. . .going with 6 1000cc ID injectors. . .
Just make sure your manifold/turbo will fit with this setup. . .this LIM moves the UIM forward a few cm's. . .mine just fits. . .
Twin oil cooler kit. . .very cool. . .thanks SB Garage!
Started on the fuel system, will get the accessories on and hopefully get to the piping and ducting later today. . .
#95
Garage Hero
iTrader: (93)
make sure you check your Pressure Plate Wedge Clip before you install the motor to the trans... I fogot to check this and it ended up being bent a little.. so when I went to push the throw out bearing forward it simply pulled out of the pressure plate. Now I have to pull the motor and trans to install a new one. Talk about a pain in the ***...
#98
Full Member
Thread Starter
iTrader: (2)
Join Date: Mar 2004
Location: Canada
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
Kind of funny. . .The R33 GT-R has been my dream car since I played Gran Turismo. . .have always wanted one. . .now that I own one. . .I'm kind of bummed out. . .the FD is still more fun to drive. . .
Not much of an update, been working on the R33 for the most part this summer. . .until. . .
I drove a few friend's FD's. . .both GT35R's. . .made me forget the skyline and start focusing on the Happy Seal again. . .
Just shitty FB pics until I get home and upload the better ones. . .
295/35/18. . .a little tall but will work. . .was borrowing the tire from a shop and have since fitted a 315/30/18. . .fits a little more snug now. . .
Sakebomb Garage Twin Oil cooler kit installed. . .
315/30 Nitto NT01. . .*drools*
Up at work right now for a couple of weeks, figuring out some electrical stuff while I'm up here. . .so hopefully a better update at the end of the month. . .
Oh Battle Cat, good job on getting yours running! That much more inspiration to get mine going haha. . .
Not much of an update, been working on the R33 for the most part this summer. . .until. . .
I drove a few friend's FD's. . .both GT35R's. . .made me forget the skyline and start focusing on the Happy Seal again. . .
Just shitty FB pics until I get home and upload the better ones. . .
295/35/18. . .a little tall but will work. . .was borrowing the tire from a shop and have since fitted a 315/30/18. . .fits a little more snug now. . .
Sakebomb Garage Twin Oil cooler kit installed. . .
315/30 Nitto NT01. . .*drools*
Up at work right now for a couple of weeks, figuring out some electrical stuff while I'm up here. . .so hopefully a better update at the end of the month. . .
Oh Battle Cat, good job on getting yours running! That much more inspiration to get mine going haha. . .
#100
No problem man! Glad we could help ya out That line that connects the coolers needs to be secure! I know you're not going to leave that line hanging like that though haha.
-Dan
BTW, those rear tires are massive!
-Dan
BTW, those rear tires are massive!
__________________
SAKEBOMB GARAGE LLC
www.SAKEBOMBGARAGE.com
Specialty aftermarket parts & service // Fremont, California
Contact: info@sakebombgarage.com
SAKEBOMB GARAGE LLC
www.SAKEBOMBGARAGE.com
Specialty aftermarket parts & service // Fremont, California
Contact: info@sakebombgarage.com
Last edited by SakeBomb Garage; 06-11-12 at 12:42 AM.