My スーパー耐久 ST-3 FD3S build thread (restore JDM endurance race car )
Thread Starter
RE for life
Joined: May 2002
Posts: 1,245
Likes: 71
From: sca
Off Season testing before the aero upgrade
Rebuild the shifter with brass bushing and put amemiya Hevey shifter
Change old hks foam filter to new one , I really consider to upgrade K&N next time
Old hks filter just attract too much dirt..,.,,
Rebuild the shifter with brass bushing and put amemiya Hevey shifter
Change old hks foam filter to new one , I really consider to upgrade K&N next time
Old hks filter just attract too much dirt..,.,,
Thread Starter
RE for life
Joined: May 2002
Posts: 1,245
Likes: 71
From: sca
Strange thing happend today
Last session of the day . Finish the cool down Lap
Return to pit cut off the switch and leave the fan on
15 min later decide to move the car back to garage , zero not thing ~ car is dead ....
After Bring the volt meter out
Seen like cut off switch was broken.....
I heard this switch do go bad but this is first time happend to me in 15 years
Off Season testing before the aero upgrade
Rebuild the shifter with brass bushing and put amemiya Hevey shifter
Change old hks foam filter to new one , I really consider to upgrade K&N next time
Old hks filter just attract too much dirt..,.,,
Attachment 570400Attachment 570401Attachment 570399
Rebuild the shifter with brass bushing and put amemiya Hevey shifter
Change old hks foam filter to new one , I really consider to upgrade K&N next time
Old hks filter just attract too much dirt..,.,,
Attachment 570400Attachment 570401Attachment 570399
Thread Starter
RE for life
Joined: May 2002
Posts: 1,245
Likes: 71
From: sca
Originally Posted by Johnny Kommavongsa
where did you get the brass bushing and is the bushing the only thing you replaced during the shifter rebuild?
And the white plastic locate on the front of shifter that is oem part
Attachment 570406
Attachment 570402
Strange thing happend today
Last session of the day . Finish the cool down Lap
Return to pit cut off the switch and leave the fan on
15 min later decide to move the car back to garage , zero not thing ~ car is dead ....
After Bring the volt meter out
Seen like cut off switch was broken.....
I heard this switch do go bad but this is first time happend to me in 15 years
Strange thing happend today
Last session of the day . Finish the cool down Lap
Return to pit cut off the switch and leave the fan on
15 min later decide to move the car back to garage , zero not thing ~ car is dead ....
After Bring the volt meter out
Seen like cut off switch was broken.....
I heard this switch do go bad but this is first time happend to me in 15 years
It come with amemiya shifter
And the white plastic locate on the front of shifter that is oem part
Attachment 570406
And the white plastic locate on the front of shifter that is oem part
Attachment 570406
Mazdatrix sells an aluminum one. PN is 02-9402-0000
Thread Starter
RE for life
Joined: May 2002
Posts: 1,245
Likes: 71
From: sca
Did some more testing improve another 2 sec
To 1.52.5 as compare the 996 cup car run between1.50 to-1.52ish at same track
I still have problem on the brake bias , will replace the caliper at this off season
Love my endless brake pad very strong bite !!
Think to upgrade to endless 2 peace rotor too
Attachment 570470
To 1.52.5 as compare the 996 cup car run between1.50 to-1.52ish at same track
I still have problem on the brake bias , will replace the caliper at this off season
Love my endless brake pad very strong bite !!
Think to upgrade to endless 2 peace rotor too
Attachment 570470
Last edited by diyman25; Dec 18, 2015 at 08:24 PM.
Thread Starter
RE for life
Joined: May 2002
Posts: 1,245
Likes: 71
From: sca
Here are my video morning testing that I get
1.52
Jdm endurance race car
Stock engine . Boost about .8kg
Motec M4
On Endless zeal suspension front 28kg rear 22
Stock brake with endless brake pad
Ings aero
I think with better brake bias ,I can get to 50
Last edited by diyman25; Dec 20, 2015 at 03:52 AM.
Nice! 
You may want to consider a transmission brace. The shift **** is moving around quite a bit as the drivetrain gets loaded and unloads. That should make shifting easier, decrease chance of mis-shifts and decrease the chance of hurting the internals.
Maybe some poly engine and diff mounts too - if you don't already have them.
You may want to consider a transmission brace. The shift **** is moving around quite a bit as the drivetrain gets loaded and unloads. That should make shifting easier, decrease chance of mis-shifts and decrease the chance of hurting the internals.
Maybe some poly engine and diff mounts too - if you don't already have them.
Last edited by gracer7-rx7; Dec 20, 2015 at 01:17 PM.
Thread Starter
RE for life
Joined: May 2002
Posts: 1,245
Likes: 71
From: sca
Man compare to cup car , RX-7 is such better car , but Porsche is challenGe to drive and will feel like u are a bad *** if u have good lap time
Senior Member
Joined: Aug 2008
Posts: 493
Likes: 0
From: Belgium (2800)
Nice!
You may want to consider a transmission brace. The shift **** is moving around quite a bit as the drivetrain gets loaded and unloads. That should make shifting easier, decrease chance of mis-shifts and decrease the chance of hurting the internals.
Maybe some poly engine and diff mounts too - if you don't already have them.
You may want to consider a transmission brace. The shift **** is moving around quite a bit as the drivetrain gets loaded and unloads. That should make shifting easier, decrease chance of mis-shifts and decrease the chance of hurting the internals.
Maybe some poly engine and diff mounts too - if you don't already have them.
Thread Starter
RE for life
Joined: May 2002
Posts: 1,245
Likes: 71
From: sca
Originally Posted by gracer7-rx7
Nice!
You may want to consider a transmission brace. The shift **** is moving around quite a bit as the drivetrain gets loaded and unloads. That should make shifting easier, decrease chance of mis-shifts and decrease the chance of hurting the internals.
Maybe some poly engine and diff mounts too - if you don't already have them.
You may want to consider a transmission brace. The shift **** is moving around quite a bit as the drivetrain gets loaded and unloads. That should make shifting easier, decrease chance of mis-shifts and decrease the chance of hurting the internals.
Maybe some poly engine and diff mounts too - if you don't already have them.
The car was ST-3 endurance car from Japan
Which is pretty much stock, so my plan get the best lap time as this set up
Now I clock 1.52 , which I think is good enough for some up grade now
So during this off season I will up grade most my busing to solid one
Careful about what material you make the "solid" bushings from. If you make them out of metal for example, that could cause a lot of vibration to be transmitted through the mechanicals and loosen every nut and bolt on the engine and other parts.
Thread Starter
RE for life
Joined: May 2002
Posts: 1,245
Likes: 71
From: sca
Originally Posted by gracer7-rx7
Careful about what material you make the "solid" bushings from. If you make them out of metal for example, that could cause a lot of vibration to be transmitted through the mechanicals and loosen every nut and bolt on the engine and other parts.
The problem u mention is mostly not exist
Thread Starter
RE for life
Joined: May 2002
Posts: 1,245
Likes: 71
From: sca
Time flyby so fast, is 2016 race season already, this year will still fcous on.suspension setup since on super taigu race car every bushing need to be stock
That need to be gone asap
So I went to my good friend.
WWW.HARDRACE.COM
They make some high quality parts for FD3S
If they can use in wtac pro class champion
Is good enough for my close to stocK race car
Suspension eye candy
As u migh expect the stock toe link is pretty mess out……
Looking good
That need to be gone asap
So I went to my good friend.
WWW.HARDRACE.COM
They make some high quality parts for FD3S
If they can use in wtac pro class champion
Is good enough for my close to stocK race car
Suspension eye candy
As u migh expect the stock toe link is pretty mess out……
Looking good
