Billys 93 black on black base
#77
547hp at the flywheel
Thread Starter
iTrader: (30)
Join Date: Oct 2008
Location: Chicago
Posts: 1,223
Likes: 0
Received 0 Likes
on
0 Posts
While the properties of E85 are fantastic, the fuel stations that carry it are less than generous in the area. Ill pass. On with more pics!
Is that a meth kit I spy on the window?
Is that a meth kit I spy on the window?
#79
547hp at the flywheel
Thread Starter
iTrader: (30)
Join Date: Oct 2008
Location: Chicago
Posts: 1,223
Likes: 0
Received 0 Likes
on
0 Posts
I only have one cooler. It's a base. The stock hard lines should be ok. If I blow one up ill take it to a local shop and have it redone with 1500psi hydraulic hose
#82
547hp at the flywheel
Thread Starter
iTrader: (30)
Join Date: Oct 2008
Location: Chicago
Posts: 1,223
Likes: 0
Received 0 Likes
on
0 Posts
meth sprayer installed in the air filter:
tank mounted although ill have to figure out a new place for the oil catch can:
charging harness installed and out of the way:
water filter installed:
solenoid for meth kit installed:
Also put the PPF, drive shaft and trans brace back under the car. reinstalled the short throw. also installed my custom bracket for the avc-r sensor and solenoid. Ill try to remember to snap a couple pics of it. engine harness is back in as well.
Finally por15'd my fuel tank. im content with the job but I think another can would have made it better. ill run it and see how it goes. if **** starts to float or come off then ill remove it for a fuel cell. It should all run this weekend tho (takes 4 days for the por15 to completely cure)
tank mounted although ill have to figure out a new place for the oil catch can:
charging harness installed and out of the way:
water filter installed:
solenoid for meth kit installed:
Also put the PPF, drive shaft and trans brace back under the car. reinstalled the short throw. also installed my custom bracket for the avc-r sensor and solenoid. Ill try to remember to snap a couple pics of it. engine harness is back in as well.
Finally por15'd my fuel tank. im content with the job but I think another can would have made it better. ill run it and see how it goes. if **** starts to float or come off then ill remove it for a fuel cell. It should all run this weekend tho (takes 4 days for the por15 to completely cure)
#83
547hp at the flywheel
Thread Starter
iTrader: (30)
Join Date: Oct 2008
Location: Chicago
Posts: 1,223
Likes: 0
Received 0 Likes
on
0 Posts
I picked up this hood from a buddy of mine that has a P-R-I-S-T-I-N-E 36k mile BB PEP FD/ Im not sure the rest of the car will polish up as nice... may have to take a brillo pad to it
All that's left is some vacuum/boost lines and bleed the clutch under the hood:
Tomorrow Ill finish up wiring the interior, put the gauge cluster back in, put the fuel tank and pump assembly in, battery, and exhaust and call it a day until Steve Kahn shows up . Ill post a few more pictures until its done tho. don't you worry
All that's left is some vacuum/boost lines and bleed the clutch under the hood:
Tomorrow Ill finish up wiring the interior, put the gauge cluster back in, put the fuel tank and pump assembly in, battery, and exhaust and call it a day until Steve Kahn shows up . Ill post a few more pictures until its done tho. don't you worry
#89
547hp at the flywheel
Thread Starter
iTrader: (30)
Join Date: Oct 2008
Location: Chicago
Posts: 1,223
Likes: 0
Received 0 Likes
on
0 Posts
shes alive... just need to fix the fans not coming on at proper temp, finish the meth install, add some lines to the boost controller/wastegate and shes dyno prepped.
#92
547hp at the flywheel
Thread Starter
iTrader: (30)
Join Date: Oct 2008
Location: Chicago
Posts: 1,223
Likes: 0
Received 0 Likes
on
0 Posts
ill probably change it to youtube later today
idle-walk_zpsfed37d10.mp4 Video by ballred414 | Photobucket
idle-walk_zpsfed37d10.mp4 Video by ballred414 | Photobucket