--------------------------------------------------------------------------------

well i havent been on here for awhile with work and building my baby well over the winter i was on a quest to build a tll beast with the best stuff i could get . so i looked on here for a motor and i found one that really striked my interest from a member rotaryconcepts007 aka sean works at a lube shop in williams berg. had a freshly built bp motor wit all new seals new this that and the other talked a real good one .drove 5 hrs to williamsberg va to see the motor i started and ran fine. went home slept on it came back the next week to buy it got it home then we started the project garrett t70 turbo, hks 50 mm wastegate, 4 1600 cc injectors. 2 wallboro fuel pumps lines, kg parts fuel rails , apexi power fc with adaptor harness from banzi-racing great product by the way. after months of building this beast and about ten grand in parts i start her up success major hard on lol then the problem occurs 2 days before the dyno visit to pfs supercars (great guys) major oil leak in the rear housing **** the dyno is 2 days away temp fix it with silicon. wait till next day to see if it worked sweet it did drove around the block making 2 psi of boost needs dyno tuned no leaks sweet major hard on. go home call it a day . next day starts up fine let her warm up for break in since io was told there were ony 1 thousand miles on it no leaks eaither dyno tomarrow . well here is where the **** hits the fan dyno day start her up drive it to the end of the block to put her on the trailer cause there is no room to turn around on our street get to the trailer it stalls out on its own ok i thought ill just get the trailer open and she will be fine nope she dont wanna start **** what happened get it in the garage check the plugs maybe the got fouled out nope they are fine flodded maybe crank it over with no plugs in the bottom **** compression sounds funny hmm check it sure enough 65 psi front 80 rear mother ****** i got the shaft tear the motor down everything was used seals springs the whole thing was garbage rear iron was cracked i 3 spots near the oil filter damn all that money for a ******* paper weight housings were flaking like a mo fo so needless to say that ****** sean aka rotaryconcepts007 is a ******* liar i paid for a fuclking piece of **** you got me but if you read this little boy i believe you said to me that you hate scammers and that bad karma is a mother ****** well guess what you fucked me bad now its time for you to pay


ROTARYCONCEPTS007 is a ******* LIAR and a thief dont trust him works at a lube shoppe in williams berg va

remember buddy bad karma is a mother ******

 

if any one has any comments my other sn on the forum for my shop is theheartbeatstopshere if you have any thingg to add feel free

 

That really sucks. If it was me I would be at the guy's house...Was there a bill of sale or anything written up and signed stating the condition of the motor? Maybe I can help you out on a rebuild.

 

This punk SCREWED me over too . He was a friend before this all happenned . He is POS and time is going to be his worst friend . I hope you have some type of receipt or maybe even print out his PM's to you . Come back to New Port News and spend $ 30.00 and let the judge handle it out from there .

Good luck

Let me know if I can help out in any way .

Va

 

This thread should of originally been started in this section. I moved it from another forum here.

Any other member that has had trouble with this member or under the name of
GlitchRX7 please post here.

 

I honestly don't get why this is his fault (based on your description of the events...which I may have misinterpreted. Next time use some punctuation, please). The engine had barely been broken in, and you were taking it to the dyno? It started and worked fine before you added stuff to it, then it broke, and now it's his fault?

Not sticking up for a bad guy, here...check around this section and you'll see I don't do anything like that. I was screwed over on this board, too, and hate scammers more than anything. However, if it worked fine when you bought it - I don't see how it's automatically his fault that it didn't work after you added stuff to it.

 

Did you read about the condition of the engine when he tore it down. It was supposed to be a fresh rebuild.

 

Another reference thread concerning this members integrity.

https://www.rx7club.com/questions-about-members-102/beware-rotaryconcepts007-624494/

 

OK, I re-read that and see what he's talking about. Honestly, once I start in on a post that long without proper grammar, spacing, or paragraphs my eyes start to gloss over.

That sucks, and thanks for the extra link. Can't stand people who sell things in a different condition than it actually is, as if the buyer isn't going to eventually find out, or be able to do anything once they do.