Lex89

Hi all,


I'm a new member and apologise if this post is in the wrong area.


ok so I have a 1993 fd rx7 stock rear end other than the following:

​​​coilovers

hardrace trailing arms

Hardrace toe arms

And superpro polyurethane bushes.


I have a problem I can not figure out and its doing my head in.

My rear drivers side ( right hand side ) hub and wheel stick out further out the rear guard compared to the left hand side.

The difference is approx 10-15mm.

It's as if the wheel offsets are different, however they are not.

it seems like the rear cradle has shifted the whole suspension to right. I dont know how this is possible because it has locator studs as well as the bolts, so im lost.


The following things to note

- a couple of years ago, I had a broken PPF replaced, both engine mounts replaced and polyurethane diff bushes installed at the same time. I also changed my aftermarket wheels at the same time. I am not 100% sure if the issue started after doing those things, but I suspect it could have because the car never had the issue before that. ( unless the aftermarket wheels I bought it with had different offsets to make it look straight )

- the car drives very straight

- the chassis is not bent

- the driveshafts are seated properly

- there is no unusual knocks or noises from the rear

- the upper and lower control arms are the same length

- the camber is not the issue because even if i reset the camber to zero on both sides, it is still not straight.

- the rear guards both look the same

- I didn't check the offset of the old wheels because I bought the car with them on the car and now they have been sold.

- the front of the car does not have the same issue.

- the rear subframe does not appear to have any cracks and doesn't look bent from what I can see.


I'm looking for some ideas, solutions and would appreciate your help so much. This issue has been bugging me for so long and I'm at boiling point.


- my thoughts are that possibly the engine mounts, ppf, and diff need to be loosened and re aligned to shift the diff to the left. However I'm not sure if there is adjustment there as the subframe has locator pins and doesn't look like it can be re aligned.


please help

Molotovman

iTrader: (49)

Pull the wheels off, place a straight edge across the back of each wheel, and physically measure the backspacing. Since you're not experience issues while driving the wheel is wrong, the hub is wrong, or there is body damage.

Billj747

Swap wheels right to left and see if the offset stays the same.

Remove the lateral rear lower control arm and see if the power flex bushing that was installed was an offset bushing that was not installed the same right to left.

Lex89

Thank you for your fast replies.
The wheels on the car are near new and are exactly the same. I have measured them as well. They are enkei, +15 offset. Both should be approx in line with the edge of the rear guard, however the left side sits inside the guard and the right side sits at least 10mm outside the guard.
The bushes on both the top and lower control arms are normal superpro bushes, none of them are offset. And the bushes do not have a left or right, they are the same for both sides.
iv measured the control arms, they are the same, none are bent.
The hubs look the same, the drive shafts are the same length also.

Molotovman

iTrader: (49)

Is one of your upper control arms installed upside down?

DaleClark

iTrader: (55)

Few ideas for you -

First, take the 1 minute and swap the wheels side to side. Super quick and will rule that out. It's possible one was mislabeled or something. Do the easy stuff, check that off the list first.

Next is gonna be the not fun part - comparing each side to find what is different. The upper Y-shaped arm can be installed upside-down and will do very weird stuff so that's worth verifying. Take a picture of one side then go to the other side and compare.

Finally start measuring things. You can use a string or something simple, doesn't have to be some super precise measurement. This is like one of those "spot the difference in the pictures" - you have to find what is different between the 2 sides.

This is not a common issue, there is something weird going on here. You're gonna have to dig in and find out why. Post pics if you need another set of eyes to check things out.

Dale

Lex89

Thank you again for your ideas and replies.
I have tried swapping the wheels over and it made no difference.
with the wheels off, you can visually see the hubs are not the same on both sides. One sits further in than the other.
The upper control arms are not install upside down( Iv removed them and checked over, measured etc)

I have also measured the wheel wells and both appear to be the same. Iv measured from imchassis to out edge of the guard, and seems the same.
the only thing I haven't measured is the subframe, I'm trying to leave removing it to last resort.

gracer7-rx7

iTrader: (16)

post pics of those hubs and uprights

Lex89

Left hand side - sitting further inside the guard

Right side - sitting further towards the outside of the guard

Lex89

Note rear right side wheel compared to the photo of the left.

Note the rear left hand side, wheel sitting inside the guard. Wheel offset is +38 19inch.

Not the right hand side rear sitting almost in line with the rear guard lip. Wheels are 19inch, +38

Valkyrie

Get it up on a lift and take *detailed* photos of your subframe and suspension.

Mostly likely you have improperly installed offset bushings, with one side set all the way in, and one side set all the way out.

It's possible your installer didn't know what he was doing. Or Superpro sent the wrong bushings.

Also, make sure the trailing arms are the same length. You might have set them to different lengths and used the toe rods to compensate.

Lex89

Ok I will take more photos tonight and post them.

But I have checked all the bushes that I have replaced, they are all the same and none are offset.
Plus if they WERE offset or wrong bushes, that could only affect the lower control arm which controls the camber. The upper arm still remains in the same position, meaning the whole hub/wheel CANNOT move.
the only way I can see the whole hub/wheel shifting is if I had adjustable upper control arms and aftermarket lower arms with lots of camber adjustment.
Only other ways are
1 - the subframe shifted/bent ( unlikely )
2 - somehow the subframe, ppf and engine mounts are not aligned properly ( not sure if there is much adjustment in them )
3 - maybe diff bushes are installed wrong or something and the whole diff/subframe has shifted? ( not sure if possible )

I'm stuck for ideas, so your ideas and help is much appreciated.

Valkyrie

That is not true. You could offset the entire hub with top and bottom offset bushings. That said, I don't know if Superpro makes offset upper bushings for both the front and rear.

Half an inch offset on one side, half an inch on the other side, and you've shifted the entire suspension by one inch.

Diff bushes aren't going to move the hubs.

It's unlikely that *both* of your subframes (front and rear) are off in the exactly same way.

I am assuming the car hasn't been in a massive accident.

Lex89

Yes you are right, you can offset the hub with offset rear upper and lower bushes, but none of my superpro bushes are offset, they are standard polyurethane replacements for the oem ones. I have pulled out the arms and double checked again.
the car has NOT been in a major accident either.

and also just to confirm, the front subframe/wheels/hubs are all normal as they should be. No issues at all.

It is ONLY the REAR that has the offset issue.

billyboy

Nothing stupid like a centering ring stuck on the hub stopping the wheel seating properly? If the suspension "wishbones" are non-adjustable and constrained upper and lower by the subframe, that's dictating wheel position basically.

Diff is suspended off the subframe and won't affect it's position. When making one piece diff bushes several years ago, there is a 5.5mm wide lip on each, needed to replicate the rubber donut on the stock mounts. I suppose in theory (with a dash of incompetence!), they could be installed wrong to shift the diff across, but that would be taken up by plunge in the tripod and CV.

I'd be checking a few pick-up diagonals to verify things are good if nothing stands out. I'm not sure if there's a body repair manual uploaded to the site anywhere? Bookworks - wherever they're located now - would be another option for factory manuals if you light cigars with $100 notes.

Lex89

Unfortunately it's not the hub rings or anything like that because even with the wheels off, you can visually see that the hubs are not the centred the same.
Iv measured both left and right ( as best I could ), the rear guard from chassis to lip, diff centre to hub, and subframe lower control arm mounting point to hub. All appear to be the same or similar.

boostin13b

Maybe its just the angle of that picture but that Quarter panel almost looks like it was pulled out a bit and doesn't look like the factory body lines, the lighting makes it hard to see

Molotovman

iTrader: (49)

Yep. It looks like the car has been wrecked to me

j9fd3s

iTrader: (3)

stone guard is missing, so its at least been repainted. also front end doesn't match the rest of the car

i'd start measuring like Billy boy says, manual is here https://foxed.ca/rx7manual/manuals/F...p%20manual.pdf

1badFB

iTrader: (1)

Fender lip to inner wheel well measurements on both sides, as well as hub flange to inner wheel well. Should tell the story.

Lex89

I had the car resprayed many years ago but it definitely hasn't been hit. The rear quarters have not been repaired other than a couple of small trolley dings.
it is probably the lighting of the photos that makes it look that way. I will take more photos.
I have measured the wheel well to lip, and both sides are the same.

Is there any adjustment in the engine mounts?

I know there is a bit of adjustment in the PPF from the transmission side.

Is there any adjustment in the sub frame?

ptrhahn

iTrader: (9)

That's not just a little off, it looks like INCHES different. It would be hard to repair an accident and have it look even semi normal with it that far off. I'm better on something mis-installed.

However—is it just an illusion, or is the front wheel tucked in more on the left than the right as well? That may be an illusion, but the rear definitely isn't.

billyboy

Fixed by 4 or 5 fasteners each side and locating dowels - you're not going to find adjustment there.

Engine mounts or PPF, will again have no bearing on what happens at the wheels, that's clutching at straws I'd say. Longshot, the aluminium uprights have been known to be damaged by hamfisted mechanics pressing bearings and I guess bad kerbing could damage something too, but would think damage there would be fairly obvious to the naked eye.

gracer7-rx7

iTrader: (16)

Post pics of the actual hubs and suspension. Facing the wheel well.

Lex89

The front is definitely not off. so must just be the angle or lighting of the photos.

I will take more photos and post them up.

I have also removed and measured the top and bottom control arms on both sides to compare. There is no issue there. Both L and R are the same.

I can't see it bieng anything other than a twisted/bent subframe. But visually from underneath the car looking at the subframe i cant see any kinks, twists or signs of damage.