airborne

WTF? Dealer wants $160 per rotor for the rears. Best deal I found was autozone for $85 each. Anyone got a better price?

Front brembo replacements from the rack were $60 each. BTW, any problem going with brembo up front and duralast in the rear? stock repacements are pretty much the same right?

DaleClark

iTrader: (55)

First off, the local dealer will rape you on price - get your parts from Malloy. But, the OEM rotors are still rather pricey.

Aftermarket rotors should be fine on a street driven car, especially on the back. I do prefer sticking with "regular" rotors and not cross drilled/slotted rotors. Big reason is you can't turn slotted or cross drilled rotors as they wear.

Brakewarehouse.com has some pretty good prices on rotors as well - might wanna check them out too.

Dale

airborne

Ray's got em for $127. Said he had plated drilled/slotted for less that he uses. Didn't think the OEMs were any better than other brands. "Thats one of those parts thats just too much." No kidding.

Brakewarehouse did have "valuemaxx" rotors for $60 but I don't like something with the word "value" in it being responsible for stopping the car. No warranty info on them either. $85 duralast with a 2yr warranty from the zone it is.

Random question: my rear outside pad was worn on an angle -symtom of...???

Sled Driver

iTrader: (9)

WTF ????????????? News to me.

I got my 5 year old rear cross drilled brembos turned a couple of months ago. ($7ea)

My only complaint was that they didn't countersink the holes after they resurfaced the rotors. So I had to do it myself at home.

IRPerformance

iTrader: (41)

Look through the vendors. You can get cross-drilled or slotted rotors for that price.

XSTransAm

http://cgi.ebay.com/ebaymotors/81-95...16632106QQrdZ1

FDNewbie

iTrader: (10)

I can get you Brembo rotors front & rear replacement rotors (yes, rears are Bradi, since Brembo doesn't make rotors for the rear in stock size) for less than any RX7 vendor, and with no additional cost for being drilled, slotted, both, and/or zinc plated PM me if you're interested.

~Ramy

Jack

iTrader: (2)

http://www.tripointengineering.com/i...9d52c9df74b71f

sonix7

damn those are cheap!! Looks like I will be contacting you Ramy for some of those, can you still do it after the first of the year. Car is down anyway.

TwinTriangles

Are they beyond getting resufaced and just nee to be replaced?

Sgtblue

iTrader: (16)

Any worries about them still being in balance?

FDNewbie

iTrader: (10)

Lemme state my disclaimer: my price is worthwhile only if you're going to slot, drill, both, and/or zinc coat 'em. Other guys sell the bare (uncoated) plain rotors for cheaper. I don't mess w/ that. You can get those dirt cheap from the link above or Tire Rack

Jason, my prices are always good. If a supplier's costs go up, every vendor's price will go up, including mine, and I'll still aim to undercut everyone Such is the beauty of wholesale accounts w/o ANY overhead, employees, facility expenses, etc

sonix7

yes sir. that is a beautiful thing. I will let you know when I am ready.

cymrex

iTrader: (2)

Nopi claims to have rear Brembo rotors for 49.35 each. I did get fronts and they were Brembo for 40.99 each. They also have a good price on NGK ignition wire set for 21.37 and spark plugs BUR9EQP and BUR7EQP for 6.81 each. NGK/NTK OE Oxygen Sensor 34.26.

That is about all I get from NOPI, but it has always been as advertised.