real quick help needed
#1
DETH TRP
Thread Starter
iTrader: (7)
Join Date: Mar 2004
Location: Manhattan Beach, CA
Posts: 2,544
Likes: 0
Received 0 Likes
on
0 Posts
real quick help needed
To clear the ABS computer's error codes I've read to connect the GND and TBS terminals in the Diagnostic box. See if you can find this mysterious port in the pic below.
#3
DETH TRP
Thread Starter
iTrader: (7)
Join Date: Mar 2004
Location: Manhattan Beach, CA
Posts: 2,544
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by mgoddard1
That's right next to the fuse block by the battery.
where can i find the TBS port so I can reset my ABS error codes?
#4
RX-7 Bad Ass
iTrader: (55)
I don't believe there's any diagnostic port for the ABS system. I checked my shop manual (Section P) and the system is pretty simple. The ABS control unit is in the hatch - inputs are the wheel speed sensors, and output is the ABS pump and the "ABS" light in the dash.
If you have an ABS light due to a code, try disconnecting the negative battery terminal, holding the brake pedal down for 10 seconds or so, then reconnecting.
The only electrical test procedure outlined in the shop manual is with the special Mazda tool.
I believe the most common problems with the ABS system are in the wheel speed sensors. Visually inspect all of them, make sure there isn't crud on them keeping them from taking a reading, and make sure the wiring to the sensors isn't damaged.
Dale
If you have an ABS light due to a code, try disconnecting the negative battery terminal, holding the brake pedal down for 10 seconds or so, then reconnecting.
The only electrical test procedure outlined in the shop manual is with the special Mazda tool.
I believe the most common problems with the ABS system are in the wheel speed sensors. Visually inspect all of them, make sure there isn't crud on them keeping them from taking a reading, and make sure the wiring to the sensors isn't damaged.
Dale
#5
DETH TRP
Thread Starter
iTrader: (7)
Join Date: Mar 2004
Location: Manhattan Beach, CA
Posts: 2,544
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by DaleClark
I don't believe there's any diagnostic port for the ABS system. I checked my shop manual (Section P) and the system is pretty simple. The ABS control unit is in the hatch - inputs are the wheel speed sensors, and output is the ABS pump and the "ABS" light in the dash.
If you have an ABS light due to a code, try disconnecting the negative battery terminal, holding the brake pedal down for 10 seconds or so, then reconnecting.
The only electrical test procedure outlined in the shop manual is with the special Mazda tool.
I believe the most common problems with the ABS system are in the wheel speed sensors. Visually inspect all of them, make sure there isn't crud on them keeping them from taking a reading, and make sure the wiring to the sensors isn't damaged.
Dale
If you have an ABS light due to a code, try disconnecting the negative battery terminal, holding the brake pedal down for 10 seconds or so, then reconnecting.
The only electrical test procedure outlined in the shop manual is with the special Mazda tool.
I believe the most common problems with the ABS system are in the wheel speed sensors. Visually inspect all of them, make sure there isn't crud on them keeping them from taking a reading, and make sure the wiring to the sensors isn't damaged.
Dale
just found out that port isn't on 93's, only on later cars. I'm pretty sure my light is on just because of a stored error code from when my ABS sensor wire was severed (the whole sensor has since been replaced and the brakes bled). I'll try resetting by pulling the fuse for a while, and then with the battery if needed. I'll let you guys know.
Trending Topics
#8
I luv my carbon footprint
Join Date: Mar 2002
Location: Indianapolis
Posts: 452
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 4CN Air
I know where the diagnostic box is, i took that picture, but I took it to show that there is no "TBS" port in the box, at least not mine
where can i find the TBS port so I can reset my ABS error codes?
where can i find the TBS port so I can reset my ABS error codes?
Thread
Thread Starter
Forum
Replies
Last Post