Q: Why not remove suspension arm on an FD?
#1
Belligerent MoFo
Thread Starter
Q: Why not remove suspension arm on an FD?
I need to change my pillow ball bushings. I've read up on a few threads the different approaches to changing the bushings.
I haven't heard why some people don't want to remove the suspension arm to remove the pillow ball bushings. Any reasons? Difficult putting back in? Suspension difficult to get back in? I read Max Coopers excellent write-up but I kept wondering why not take out the suspension arm? Any help would be appreciated.
Also, any other bushings or components I should change. I don't have any side to side play on the rear wheels so I don't think I need any toe-links. Car has about 62K miles on it.
Thanks
Victor
I haven't heard why some people don't want to remove the suspension arm to remove the pillow ball bushings. Any reasons? Difficult putting back in? Suspension difficult to get back in? I read Max Coopers excellent write-up but I kept wondering why not take out the suspension arm? Any help would be appreciated.
Also, any other bushings or components I should change. I don't have any side to side play on the rear wheels so I don't think I need any toe-links. Car has about 62K miles on it.
Thanks
Victor
Last edited by vchacon; 04-30-05 at 05:03 PM.
#2
RX-7 Bad Ass
iTrader: (55)
Read my write-up -
http://www.clubrx.org/default.asp?id...ntent=32&mnu=5
I removed the suspension arms. It went VERY quickly and smoothly, but I did have air tools, which makes the job a MILLION times easier.
I don't see any reason to not remove them, save for there's more tough bolts you have to loosen. IMHO you save way more time being able to manipulate the parts off the car than trying to fight inside the wheel well of the car.
Dale
http://www.clubrx.org/default.asp?id...ntent=32&mnu=5
I removed the suspension arms. It went VERY quickly and smoothly, but I did have air tools, which makes the job a MILLION times easier.
I don't see any reason to not remove them, save for there's more tough bolts you have to loosen. IMHO you save way more time being able to manipulate the parts off the car than trying to fight inside the wheel well of the car.
Dale
#4
wants some ube
Sgtblue: First off, I love your avatar (my dad is a sgt for pd too). Replacing the bushings is something that I need to complete sometime in the future. I have read previous threads about the bushings, but I was wondering how much the replacing set you back. Which bushings did you use? Open to any comments. I want that clunk to be gone before my fd is in comission again.
edit: ok, so I just read the linked write-up, and saw prices and what not. Still open to any comments though.
edit: ok, so I just read the linked write-up, and saw prices and what not. Still open to any comments though.
#5
Urban Combat Vet
iTrader: (16)
Robbyah,
I'm far from an authority, but when I first got my car the rear suspension was making alot of noise. After searching here everything pointed toward the pillowball bushings. Since then I've replaced four of the six rear bushings which cured about 75% of the noise. Still have a little clunking which seems to be at it's worse when the rear is the lightest (< 1/4 tank of gas) and at slow speed. I hope that by replacing those last two in each toe-link helps. With the other bushings I took off the suspension pieces and had a local shop press the old out and new in. Wasn't too costly but I've got a balljoint press and may try DaleClark's method with these last two.
There are tons of threads on suspension noise and pillow-ball bushings.
Tell your Dad to be careful and good luck.
I'm far from an authority, but when I first got my car the rear suspension was making alot of noise. After searching here everything pointed toward the pillowball bushings. Since then I've replaced four of the six rear bushings which cured about 75% of the noise. Still have a little clunking which seems to be at it's worse when the rear is the lightest (< 1/4 tank of gas) and at slow speed. I hope that by replacing those last two in each toe-link helps. With the other bushings I took off the suspension pieces and had a local shop press the old out and new in. Wasn't too costly but I've got a balljoint press and may try DaleClark's method with these last two.
There are tons of threads on suspension noise and pillow-ball bushings.
Tell your Dad to be careful and good luck.
#6
gross polluter
iTrader: (2)
The pillow ***** are easy enough to replace with the a-arms in place, removing them is just extra bolts to pull. If you have air tools it may be no big deal but I cant imagine it making things much easier.
To know if it is the toe links grab a rear wheel and see if you can get it to clunk by steering it side to side. For me the toe links were about90% of the noise.
You most likely wont be able to use a press to get the pillow ***** out of the toe link with a press, they will need to be cut out. The shape of the toe link just doesnt give you a good place to steady it on the press. No big deal, just have a hack saw available when you get there.
Originally Posted by Sgtblue
With the other bushings I took off the suspension pieces and had a local shop press the old out and new in. Wasn't too costly but I've got a balljoint press and may try DaleClark's method with these last two.
There are tons of threads on suspension noise and pillow-ball bushings.
There are tons of threads on suspension noise and pillow-ball bushings.
You most likely wont be able to use a press to get the pillow ***** out of the toe link with a press, they will need to be cut out. The shape of the toe link just doesnt give you a good place to steady it on the press. No big deal, just have a hack saw available when you get there.
#7
Super Snuggles
Originally Posted by Tom93R1
You most likely wont be able to use a press to get the pillow ***** out of the toe link with a press, they will need to be cut out. The shape of the toe link just doesnt give you a good place to steady it on the press. No big deal, just have a hack saw available when you get there.
Trending Topics
#8
Urban Combat Vet
iTrader: (16)
Originally Posted by Tom93R1
.... You most likely wont be able to use a press to get the pillow ***** out of the toe link with a press, they will need to be cut out. The shape of the toe link just doesnt give you a good place to steady it on the press. No big deal, just have a hack saw available when you get there.
Tom, I haven't taken a close look at it lately, but I was referring to the smaller bushings, the ones at the opposite end of the toe link from those being changed in JimLab's pictures. Those don't require the hacksaw...or do they?
#9
Belligerent MoFo
Thread Starter
So, I go to change my pillow ball bushings and take a hold of the toe-link and what do you know... I can rotate it along is long axis. I can't move it back and forth but I can rotate it clockwise and counter clockwise a bit. I assume this also means I'll need to bushing for these
Anyone have part numbers.... do I just get a new set of toe-links? I suppose I'll do a little searching after I replace the pillow *****.
Victor
Anyone have part numbers.... do I just get a new set of toe-links? I suppose I'll do a little searching after I replace the pillow *****.
Victor
#11
Urban Combat Vet
iTrader: (16)
Originally Posted by vchacon
So, I go to change my pillow ball bushings and take a hold of the toe-link and what do you know... I can rotate it along is long axis. I can't move it back and forth but I can rotate it clockwise and counter clockwise a bit. I assume this also means I'll need to bushing for these
Anyone have part numbers.... do I just get a new set of toe-links? I suppose I'll do a little searching after I replace the pillow *****.
Victor
Anyone have part numbers.... do I just get a new set of toe-links? I suppose I'll do a little searching after I replace the pillow *****.
Victor
https://www.rx7club.com/showthread.p...ight=toe+links
There are aftermarket toe-links available or the bushings at either (or both) ends can be replaced.
Last edited by Sgtblue; 05-01-05 at 04:22 PM.
#12
Belligerent MoFo
Thread Starter
Guys, a little help here, I think I fucked up my control arm. I was using a pillow ball clamp to push in the bushing and I over tightened it... the bushing pushed through to the other side. So, I pushed back in to about the right position but the "ridge" that was there isn't structural sound anymore... NEW ARM?
Thanks
Victor
Thanks
Victor
#14
gross polluter
iTrader: (2)
I thought he meant a ball joint press as in the big c-clamp thing you can rent at the parts places. Most people dont have direct access to a big press like that other than going to a machine shop and if you are going to the machine shop you arent going to press them out yourself any way so it doesnt even matter.
#16
Lives on the Forum
Join Date: Dec 2001
Location: San Lorenzo, California
Posts: 14,716
Likes: 0
Received 8 Likes
on
8 Posts
Originally Posted by c h I n e Z e~BoY
what bushings do you guys reccomend?
Thread
Thread Starter
Forum
Replies
Last Post
[For Sale] Scratch & Dent, Used, and Open-Box Sale!
SakeBomb Garage
Vendor Classifieds
5
08-09-18 05:54 PM
rx7jocke
Suspension/Wheels/Tires/Brakes
72
06-17-16 03:48 AM
risingsunroof82
1st Generation Specific (1979-1985)
8
09-07-15 01:11 PM