need some input on emission's elimination
02-09-07, 01:16 PM
#1
czseven
Thread Starter
Join Date: Nov 2006
Location: florida
Posts: 163
Likes: 0
Received 0 Likes
on
0 Posts
need some input on emission's elimination
Yes I have searched and searched I have found the following. also ordered block off plates frome rx7 store includes 7. I currentially have full non sequential setup and in the process of iliminating all emissions+rats nest.I know the following.
ACV=air controll valve whare is this located?
split air=? is there a block plate for this?
AWS pipe=under uim,is there a block plate for this?
AWS solenoid= under UIM,is there a block plate for this?
EGR valve=above turbos on outside of LIM,is there a block plate for this?
ISC/BAC solenoid=what is this? whare is this?
double throttle=I do know this one and what to do abought it.
I am going to be running a stock ECU for a while as well and yes I will be placing resistors in the specified places. just wanted to know what all i can block off and whare it might be located, any help on this would be great, i just don't know what all these(aws,egr,isc,etc etc) do and are located.
ACV=air controll valve whare is this located?
split air=? is there a block plate for this?
AWS pipe=under uim,is there a block plate for this?
AWS solenoid= under UIM,is there a block plate for this?
EGR valve=above turbos on outside of LIM,is there a block plate for this?
ISC/BAC solenoid=what is this? whare is this?
double throttle=I do know this one and what to do abought it.
I am going to be running a stock ECU for a while as well and yes I will be placing resistors in the specified places. just wanted to know what all i can block off and whare it might be located, any help on this would be great, i just don't know what all these(aws,egr,isc,etc etc) do and are located.
02-09-07, 01:32 PM
#2
Traitor
Join Date: Dec 2006
Location: UNCC, NC
Posts: 185
Likes: 0
Received 0 Likes
on
0 Posts
DT - don't forget the thermo rod
AWS Pipe - You can remove this pipe and put on a block off plate, I just capped the pipe and the elbow with some rubber caps.
AWS - That suckers somewhere deep in the rats nest IIRC, cap off the ends and zip tie the caps, unless you want to remove the entire rats nest and remove the solenoid as well
ISC - This helps....well, this is supposed to help the car idle, serves no emissions purpose that I know of, I'd just leave it. Its the big solenoid dead center behind the UIM.
I just left the EGR but I think thats 2 lines to cap and pop on the block off plate, maybe somebody else can fill in the blanks. With stock vac lines this part of the car sucks to work on
Good Luck
AWS Pipe - You can remove this pipe and put on a block off plate, I just capped the pipe and the elbow with some rubber caps.
AWS - That suckers somewhere deep in the rats nest IIRC, cap off the ends and zip tie the caps, unless you want to remove the entire rats nest and remove the solenoid as well
ISC - This helps....well, this is supposed to help the car idle, serves no emissions purpose that I know of, I'd just leave it. Its the big solenoid dead center behind the UIM.
I just left the EGR but I think thats 2 lines to cap and pop on the block off plate, maybe somebody else can fill in the blanks. With stock vac lines this part of the car sucks to work on
Good Luck
Thread
Thread Starter
Forum
Replies
Last Post
Turblown
Vendor Classifieds
12
10-17-20 03:25 PM
ls1swap
3rd Generation Specific (1993-2002)
12
10-01-15 07:58 PM