Need Advice for New Engine
#1
26.55 psi T04Z Monster
Thread Starter
Need Advice for New Engine
Well it finally happened!!!
My 94 decided to commited suicide, but oh well I got almost a full year out of this engine. Anyways, I am in search of a good shop that make quaility 13b's. I will be looking to go with 3mm seals and a street port on this engine. I had a street port on the previous, but the shop said 3mm were a waste...yeah ok.. Well if any of you guys know some good shops that make top of the line streetable engine PLEASE respond.
Thanks
Tim
1994 RX7
"Had" 13b REW streetport
T-70 p-trim
HKS super drager
HKS sequential blow off
Broward race clutch
Custom FMIC
Unorthdox pulleys
Pettit Unlimited ECU (FOR SALE)
Cosmoz Fuel pump
Greedy Profec B
Greddy Turbo Timer
Greddy Intake Elbow (boss)
Greddy Gauges
My 94 decided to commited suicide, but oh well I got almost a full year out of this engine. Anyways, I am in search of a good shop that make quaility 13b's. I will be looking to go with 3mm seals and a street port on this engine. I had a street port on the previous, but the shop said 3mm were a waste...yeah ok.. Well if any of you guys know some good shops that make top of the line streetable engine PLEASE respond.
Thanks
Tim
1994 RX7
"Had" 13b REW streetport
T-70 p-trim
HKS super drager
HKS sequential blow off
Broward race clutch
Custom FMIC
Unorthdox pulleys
Pettit Unlimited ECU (FOR SALE)
Cosmoz Fuel pump
Greedy Profec B
Greddy Turbo Timer
Greddy Intake Elbow (boss)
Greddy Gauges
#2
Senior Member
Join Date: Mar 2001
Location: Roaring Spring, PA USA
Posts: 524
Likes: 0
Received 2 Likes
on
2 Posts
What caused your engine failure? Determine that before wasting money on 3mm seals. One ping and they break just the same as a 2mm. Once determined what caused the failure, spend the extra money to safeguard against it. Sounds like the car is built up, what safeguards do you have?? From your post, it appears the apex seal broke. Don't always assume the 3mm is going to last any longer than the 2mm.
Tim
Tim
#7
Pimpin Rotors...and Hoes
Join Date: Feb 2001
Location: New Orleans, LA
Posts: 1,401
Likes: 0
Received 0 Likes
on
0 Posts
BTW, what was the cause of your engine failure?? I see that you had an Intercooler and Pettit unlimited, and fuel pump. Were you just running excessively high on the boost or something??
Trending Topics
#8
26.55 psi T04Z Monster
Thread Starter
Well if I was to take a stab at what caused my engine failure..
1st off it had a fan failure caused by a poor filter placement on the fans. This caused a short in the fan motor, which equaled a sky-rocketing temp. The engine seemed to be ok but then the stock turbos failed. So I upgraded to a T-70 p trim, but the boost was only at 10lbs peak. More than likely the seals were damaged during the over heat and the added boost pushed them to the edge. This is only my geuss I am not an expert by any means. I appreciate all of the advice though. I plan to safegaurd this engine far more than the last. Feel free to ask any thing else.
1st off it had a fan failure caused by a poor filter placement on the fans. This caused a short in the fan motor, which equaled a sky-rocketing temp. The engine seemed to be ok but then the stock turbos failed. So I upgraded to a T-70 p trim, but the boost was only at 10lbs peak. More than likely the seals were damaged during the over heat and the added boost pushed them to the edge. This is only my geuss I am not an expert by any means. I appreciate all of the advice though. I plan to safegaurd this engine far more than the last. Feel free to ask any thing else.
#10
Full Member
Join Date: Feb 2001
Location: Columbus,OHIO
Posts: 223
Likes: 0
Received 0 Likes
on
0 Posts
Someone on here is running 2mm ceramic seals with a streetport and i seem to remember him being very satisfied with his setup. do a search and see what advice he can give you about ceramic seals.
#11
Rotary Enthusiast
Join Date: Feb 2001
Location: In the Sky
Posts: 1,190
Likes: 0
Received 0 Likes
on
0 Posts
Rob golden at pinapple racing is the man..he does my motors
Originally posted by black99
Anyone have any experiance with pineapple racing??... From the looks of their webpage it seems they have fair prices and seem to know what they are doing...
Anyone have any experiance with pineapple racing??... From the looks of their webpage it seems they have fair prices and seem to know what they are doing...
Thread
Thread Starter
Forum
Replies
Last Post
stickmantijuana
Engine Management Forum
11
11-09-15 01:15 PM
fastrx7man
3rd Generation Specific (1993-2002)
33
09-02-15 09:42 PM