mpeg of my car on dyno shooting flames
08-19-02, 02:25 PM
#1
mpeg of my car on dyno shooting flames
http://jayatworkslackin.com/Files/MOV00610.MPG
I got my car on a dynojet this past weekend. I am waiting for a friend to scan the dyno sheet. Here is an mpeg of my car on the dyno shooting a nice flame. Oh yeah, it did 336whp and 288tq. at 14lbs. of boost
I got my car on a dynojet this past weekend. I am waiting for a friend to scan the dyno sheet. Here is an mpeg of my car on the dyno shooting a nice flame. Oh yeah, it did 336whp and 288tq. at 14lbs. of boost
Trending Topics
08-20-02, 11:25 PM
#14
Junior Member
Join Date: Aug 2002
Location: beverly hills, ca
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
looking through your mods to see what kind of fuel management you are running, only to see "ECU" hehe. so what kind of "ECU" are u running? 
chipped stock ecu?
chipped stock ecu?
08-21-02, 08:36 AM
#17
Thanks for the compliments guys
Dan, I didn't realize that I left the suspension stuff out of my sig.
Koni Yellows
Ground Control coilovers w/ pillow ball mounts
M2 Trailing arms
I had to have part of my rear fenders cut out to make room for the 12's and the 10's fit just fine up front w/ some rolling of the fender lips.
The car IS lowered, not exactly how much but more than an inch.
Happai- The ECU was tuned by Rick Stiles Supercars in El Paso. I'm hoping to go standalone around April with tax money
Dont_Be_A_Rikki, I will try to get the sheets scanned and up later today
Thanks again for the compliments Here is another link for a different run without flames.
http://comp.uark.edu/~kjharmo/dyno_rx7.mpg
Dan, I didn't realize that I left the suspension stuff out of my sig.
Koni Yellows
Ground Control coilovers w/ pillow ball mounts
M2 Trailing arms
I had to have part of my rear fenders cut out to make room for the 12's and the 10's fit just fine up front w/ some rolling of the fender lips.
The car IS lowered, not exactly how much but more than an inch.
Happai- The ECU was tuned by Rick Stiles Supercars in El Paso. I'm hoping to go standalone around April with tax money
Dont_Be_A_Rikki, I will try to get the sheets scanned and up later today
Thanks again for the compliments
Here is another link for a different run without flames.http://comp.uark.edu/~kjharmo/dyno_rx7.mpg
08-21-02, 09:26 AM
#18
Full Member
Join Date: May 2002
Location: Maine
Posts: 125
Likes: 0
Received 0 Likes
on
0 Posts
Great numbers . I also just through down abouy the same numbers as you . I did not see any flames come out of my exhaust but I did blow off the tubing that they put on the exhaust tip for the gasses .
08-21-02, 12:00 PM
#19
dyno sheet from high boost run
here is the dyno sheet from the high boost run.
dizastical- damn, your peak numbers are just about the same, kewl
. Do you have your dyno sheet scanned, I would like to compare. Also, I do not see anything about an upgraded intercooler in your sig. Have you upgraded? If not, be careful you are seriously pushing the stock intercooler WAY too much.
dizastical- damn, your peak numbers are just about the same, kewl
. Do you have your dyno sheet scanned, I would like to compare. Also, I do not see anything about an upgraded intercooler in your sig. Have you upgraded? If not, be careful you are seriously pushing the stock intercooler WAY too much.
Thread
Thread Starter
Forum
Replies
Last Post
