3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

little cleaning advise

Thread Tools
 
Search this Thread
 
Old Nov 24, 2006 | 10:33 PM
  #1  
Fsunoles06's Avatar
Thread Starter
Senior Member
Tenured Member 05 Years
 
Joined: May 2006
Posts: 292
Likes: 0
From: Pearland/Houston
little cleaning advise

I'm in the middle of a rebuild and I am currently soaking my housings, irons, and rotors in paint thinner. The carbon build up is pretty damn nasty on the rotors and the paint thinner just isn't cutting it. It seemed to work well on the housings, but not so much on the rotors.

I searched on this topic and saw some people used simple green and carb cleaner, but I don't know if thats going to do the job or not.

I need some real nasty stuff here that can cut through the carbon without damaging the rotor bearings.

Also is it worth cleaning out the coolant passages? I made sure to get all the bulky stuff out of there, but the passages are still orange.
Reply
Old Nov 24, 2006 | 11:21 PM
  #2  
GoodfellaFD3S's Avatar
Original Gangster/Rotary!
Veteran: Army
Tenured Member: 25 Years
Liked
Loved
iTrader: (213)
 
Joined: Mar 2001
Posts: 30,804
Likes: 646
From: FL-->NJ/NYC again!
Carb cleaner and a razor blade should work well unless your rotors are really carbon'ed up.

Re: the rotor bearings, how many miles on them? They don't need replacing?

Re: the coolant passages, as long as they are clean of debris I wouldnt' worry about the orange discoloration, that's normal.
Reply
Old Nov 25, 2006 | 12:06 AM
  #3  
Fsunoles06's Avatar
Thread Starter
Senior Member
Tenured Member 05 Years
 
Joined: May 2006
Posts: 292
Likes: 0
From: Pearland/Houston
well i know for sure one of my rotor bearing needs replacing, either way i'll probably end up doing both. So i guess I shouldn't be that worried about them. And yes they are reaaally carboned up. My motor was actually carbon locked. You can see pictures at the bottom of this thread.

https://www.rx7club.com/showthread.p...0&page=1&pp=15
Reply
Old Nov 25, 2006 | 01:20 AM
  #4  
MirX's Avatar
Full Member
Tenured Member 05 Years
 
Joined: Sep 2006
Posts: 57
Likes: 0
From: Australia, Perth WA
damn man thats some messy ****
when i come to haul the engine outta my fd, i going to port, seals, and bearings and makes sure allllll is clean beofre going back together lol

but hopefully im a long way off with neluck another year! lol

so i got plenty of time up my sleves LOL
Reply
Old Nov 25, 2006 | 12:16 PM
  #5  
Seventh Heaven's Avatar
Zoom - Zoom
Tenured Member 15 Years
iTrader: (1)
 
Joined: Nov 2005
Posts: 131
Likes: 0
From: California
You could try Purple. This link shows it working really well on the rotors.

https://www.rx7club.com/showthread.p...hlight=rebuild
Reply
Old Nov 25, 2006 | 01:12 PM
  #6  
trainwreck517's Avatar
Rx-hippie
Tenured Member 15 Years
iTrader: (1)
 
Joined: Sep 2003
Posts: 2,076
Likes: 0
From: Torrance CA
what brand of gas and oil where you using? Thats the worst carbon build I have ever seen.. Even my old S5 N/A motor with 170k had far less..

And as GoodfellaFD3s said,.. carb cleaner and a razor blade works wonders.
Reply
Old Nov 25, 2006 | 05:27 PM
  #7  
Fsunoles06's Avatar
Thread Starter
Senior Member
Tenured Member 05 Years
 
Joined: May 2006
Posts: 292
Likes: 0
From: Pearland/Houston
well i didn't drive the car very long before I took it town for mods and rebuilding. So I don't know what the previous owner used. It is obvious though, it was not properly maintained. Of course that will all change now.

Yes that is by far the worst carbon build up i've ever seen as well.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
josef 91 vert
2nd Generation Specific (1986-1992)
14
Sep 17, 2015 09:22 PM
younG_Gunner
2nd Generation Specific (1986-1992)
2
Sep 9, 2015 08:26 PM




All times are GMT -5. The time now is 03:51 AM.