3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

Just installed Fighters Air Intake, now BOV questions...

Thread Tools
 
Search this Thread
 
Old Apr 9, 2007 | 12:11 PM
  #1  
Seppeku's Avatar
Thread Starter
Full Member
Tenured Member 05 Years
 
Joined: Apr 2006
Posts: 143
Likes: 0
From: Phoenix
Just installed Fighters Air Intake, now BOV questions...

Hi guys!

Yesterday, I installed the Fighters Garage Air Intake and man, it's awesome! Very good quality product.

Anyway, after removing the stock airbox, I have no place for my BOV's to vent. Right now, they're just open venting, with no hose on them at all. Is that bad? If so, what should I do? If not, boy they're loud. How do I quiet them down? I don't necessarily like the purging sounds really loud. A little is ok...

Thanks for opinions and helping out!!!

I need to change my sig now too...
Reply
Old Apr 9, 2007 | 12:18 PM
  #2  
IRPerformance's Avatar
Sponsor
iTrader: (41)
 
Joined: Apr 2003
Posts: 11,347
Likes: 321
From: NJ
They should not suck in air, but if you are worried you can install small k&n filters. Any intake is going to make the car louder, especially an open one. You could try installing a lawnmover muffler on the end of the hose as some people do with the airpump.
Reply
Old Apr 9, 2007 | 12:42 PM
  #3  
Seppeku's Avatar
Thread Starter
Full Member
Tenured Member 05 Years
 
Joined: Apr 2006
Posts: 143
Likes: 0
From: Phoenix
I understand the car is going to be louder because of the open air intake, but I'm strictly talking about the BOV's noise and the venting portion.
Reply
Old Apr 9, 2007 | 12:46 PM
  #4  
rynberg's Avatar
Lives on the Forum
Tenured Member: 20 Years
 
Joined: Dec 2001
Posts: 14,716
Likes: 10
From: San Lorenzo, California
This is something you should have considered before buying an open intake.
Reply
Old Apr 9, 2007 | 01:00 PM
  #5  
Seppeku's Avatar
Thread Starter
Full Member
Tenured Member 05 Years
 
Joined: Apr 2006
Posts: 143
Likes: 0
From: Phoenix
That was helpful... Thank you for that...

I did consider this, I knew it was going to be louder. My question is if it's ok for the BOV's to be open vented or should I do something about it? That's all. And maybe someone has some helpful advice on how to quiet them down, that's all.
Reply
Old Apr 9, 2007 | 01:07 PM
  #6  
surfmon's Avatar
Rotary Enthusiast
Tenured Member 15 Years
iTrader: (6)
 
Joined: Jul 2003
Posts: 1,002
Likes: 1
From: Pensacola, FL
its fine to open vent your BOV's
If you want to quiet them a little, put a 90 degree hose on the outlets

makes a noticeable difference

t
Reply
Old Apr 9, 2007 | 01:23 PM
  #7  
Seppeku's Avatar
Thread Starter
Full Member
Tenured Member 05 Years
 
Joined: Apr 2006
Posts: 143
Likes: 0
From: Phoenix
Thank you very much!!! I think I'll get some hose and do just that...
Reply
Old Apr 9, 2007 | 02:39 PM
  #8  
IRPerformance's Avatar
Sponsor
iTrader: (41)
 
Joined: Apr 2003
Posts: 11,347
Likes: 321
From: NJ
Home depot should have some pvc 90's you can use. Routing the hoses down will definately help.
Reply
Old Apr 9, 2007 | 02:53 PM
  #9  
Mahjik's Avatar
Mr. Links
Tenured Member 20 Years
iTrader: (1)
 
Joined: Aug 2001
Posts: 27,595
Likes: 43
From: Kansas City, MO
Go to NAPA or AutoZone and ask to browse their pre-formed coolant hoses. I grabbed a long one with several bends to do some various tubing. Take the BOV off and take it in the store with you to get the correct/useable hose diameter.
Reply
Old Apr 9, 2007 | 03:14 PM
  #10  
BoostedTimmy's Avatar
Traitor
Tenured Member 15 Years
 
Joined: Dec 2006
Posts: 185
Likes: 0
From: UNCC, NC
I've running running an open BOV for a while now. For a while I had it with nothing past the BOV itself, but I noticed the hot air it dumped was tearing up the insulation on my hood (Even at idle my BOV is blowing hot air). I got about 3' of heater hose and routed it out the front of the car near the radiator, all the hot air stays out. Only problem now is everyone can hear my BOV, you know how that kind of attention goes...
Reply
Old Apr 9, 2007 | 03:26 PM
  #11  
Seppeku's Avatar
Thread Starter
Full Member
Tenured Member 05 Years
 
Joined: Apr 2006
Posts: 143
Likes: 0
From: Phoenix
Thanks guys, I appreciate the help!!!
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
BNR34RB26DETT
Build Threads
42
Feb 28, 2018 11:27 AM
gabescanlon
Interior / Exterior / Audio
1
Aug 11, 2015 05:59 PM




All times are GMT -5. The time now is 06:25 PM.