3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

Just got my car!

Old Nov 19, 2005 | 07:49 AM
  #1  
wutanec's Avatar
Thread Starter
Full Member
Tenured Member 15 Years
 
Joined: Nov 2005
Posts: 159
Likes: 0
From: Detroit, MI
Just got my car!

I just got my car yesterday! I am very excited about owning this car. I've been doing a lot of research on this car but after i got my car, i came up with some questions. First, where is the freaking dipstick?? I was looking for a engine oil dipstick in gas station to check my oil level but I couldn't find the damn thing.. another question, where should I check to see coolant level? I tried to find coolant tank but couldn't find it. It has aluminum AST I wonder if I should open it to check the coolant level? Oh and should AST be full?I was surprised that the engine room is so damn tight. It's going to be fun when I start working on it
Wish me luck with my car
Reply
Old Nov 19, 2005 | 08:07 AM
  #2  
dgeesaman's Avatar
Moderator
Tenured Member: 20 Years
Liked
Loved
iTrader: (8)
 
Joined: May 2002
Posts: 12,313
Likes: 27
From: Hershey PA
Oil dipstick:
Stand over the drivers side wheel, and look under the plastic throttle elbow. It's a thin wire handle painted in yellow.

The coolant overflow tank is behind the passenger side headlight. Check the level there, and in the coolant filler neck above the belts.

Yes, it's a tight engine bay. The stock accessories really fill things up - many modified engines remove/disable/block off some of these things.

Dave
Reply
Old Nov 19, 2005 | 08:19 AM
  #3  
jasonlel's Avatar
Junior Member
Tenured Member 10 Years
 
Joined: Mar 2001
Posts: 38
Likes: 1
From: Malaysia
Talking

Take a look at the picture I attached (is a right hand drive car).

FD has 3 coolant filling point. Uncap the AST and the center filling point. Fill up the center filling point till the AST is full (while filling up, you will see the water level in AST raise). Then cap the AST and continue to fill the center filling point till it is full. Do fill up the 3rd filling point if you want....

*perform it when the engine is not HOT!!!!!




Originally Posted by wutanec
I just got my car yesterday! I am very excited about owning this car. I've been doing a lot of research on this car but after i got my car, i came up with some questions. First, where is the freaking dipstick?? I was looking for a engine oil dipstick in gas station to check my oil level but I couldn't find the damn thing.. another question, where should I check to see coolant level? I tried to find coolant tank but couldn't find it. It has aluminum AST I wonder if I should open it to check the coolant level? Oh and should AST be full?I was surprised that the engine room is so damn tight. It's going to be fun when I start working on it
Wish me luck with my car
Attached Thumbnails Just got my car!-engine_bay.jpg  
Reply
Old Nov 19, 2005 | 01:53 PM
  #4  
wutanec's Avatar
Thread Starter
Full Member
Tenured Member 15 Years
 
Joined: Nov 2005
Posts: 159
Likes: 0
From: Detroit, MI
Thanks guys. I'm going to my car right now to check.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
fastrx7man
3rd Generation Specific (1993-2002)
33
Sep 2, 2015 09:42 PM
smikels
2nd Generation Specific (1986-1992)
3
Aug 18, 2015 01:26 PM
Junkee
New Member RX-7 Technical
2
Aug 15, 2015 01:57 PM


Thread Tools
Search this Thread

All times are GMT -5. The time now is 05:00 AM.