3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

Just got my car!

Thread Tools
 
Search this Thread
 
Old 11-19-05, 07:49 AM
  #1  
Full Member

Thread Starter
 
wutanec's Avatar
 
Join Date: Nov 2005
Location: Detroit, MI
Posts: 159
Likes: 0
Received 0 Likes on 0 Posts
Just got my car!

I just got my car yesterday! I am very excited about owning this car. I've been doing a lot of research on this car but after i got my car, i came up with some questions. First, where is the freaking dipstick?? I was looking for a engine oil dipstick in gas station to check my oil level but I couldn't find the damn thing.. another question, where should I check to see coolant level? I tried to find coolant tank but couldn't find it. It has aluminum AST I wonder if I should open it to check the coolant level? Oh and should AST be full?I was surprised that the engine room is so damn tight. It's going to be fun when I start working on it
Wish me luck with my car
Old 11-19-05, 08:07 AM
  #2  
Moderator

iTrader: (7)
 
dgeesaman's Avatar
 
Join Date: May 2002
Location: Fort Kickass
Posts: 12,302
Received 16 Likes on 15 Posts
Oil dipstick:
Stand over the drivers side wheel, and look under the plastic throttle elbow. It's a thin wire handle painted in yellow.

The coolant overflow tank is behind the passenger side headlight. Check the level there, and in the coolant filler neck above the belts.

Yes, it's a tight engine bay. The stock accessories really fill things up - many modified engines remove/disable/block off some of these things.

Dave
Old 11-19-05, 08:19 AM
  #3  
Junior Member

 
jasonlel's Avatar
 
Join Date: Mar 2001
Location: Malaysia
Posts: 38
Likes: 0
Received 1 Like on 1 Post
Talking

Take a look at the picture I attached (is a right hand drive car).

FD has 3 coolant filling point. Uncap the AST and the center filling point. Fill up the center filling point till the AST is full (while filling up, you will see the water level in AST raise). Then cap the AST and continue to fill the center filling point till it is full. Do fill up the 3rd filling point if you want....

*perform it when the engine is not HOT!!!!!




Originally Posted by wutanec
I just got my car yesterday! I am very excited about owning this car. I've been doing a lot of research on this car but after i got my car, i came up with some questions. First, where is the freaking dipstick?? I was looking for a engine oil dipstick in gas station to check my oil level but I couldn't find the damn thing.. another question, where should I check to see coolant level? I tried to find coolant tank but couldn't find it. It has aluminum AST I wonder if I should open it to check the coolant level? Oh and should AST be full?I was surprised that the engine room is so damn tight. It's going to be fun when I start working on it
Wish me luck with my car
Attached Thumbnails Just got my car!-engine_bay.jpg  
Old 11-19-05, 01:53 PM
  #4  
Full Member

Thread Starter
 
wutanec's Avatar
 
Join Date: Nov 2005
Location: Detroit, MI
Posts: 159
Likes: 0
Received 0 Likes on 0 Posts
Thanks guys. I'm going to my car right now to check.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
fastrx7man
3rd Generation Specific (1993-2002)
33
09-02-15 09:42 PM
smikels
2nd Generation Specific (1986-1992)
3
08-18-15 01:26 PM
Junkee
New Member RX-7 Technical
2
08-15-15 01:57 PM



Quick Reply: Just got my car!



All times are GMT -5. The time now is 12:41 PM.