How to re-tap oxygen sensor threads?
#1
How to re-tap oxygen sensor threads?
Aftermarket downpipe, a couple of slightly damaged threads. Most of the threads are undamaged.
Anyone know of a good way to fix this without needing to weld in another bung? Is there a tap out there I could buy/rent/borrow for chasing them out?
Dave
Anyone know of a good way to fix this without needing to weld in another bung? Is there a tap out there I could buy/rent/borrow for chasing them out?
Dave
#2
Eats, Sleeps, Dreams Rotary
iTrader: (2)
Join Date: Nov 2002
Location: LA, CA
Posts: 3,332
Likes: 0
Received 0 Likes
on
0 Posts
you should be able to find a tap, but it's going to be pricy. all the good taps are usually carbide or something like that and since it's big it's $$$.
my suggestion is find a SS bolt that is the same size and work that in and out a few times with some lubricant.
my suggestion is find a SS bolt that is the same size and work that in and out a few times with some lubricant.
#4
All Spooled Up
iTrader: (7)
Negative - here is the tap you need, 18mm x 1.50 thread. Here it is at Amazon - http://www.amazon.com/1-5-High-Speed.../dp/B0006G4N7Y. It is not that much.
This is a common tap. You could simply go by your local machine shop and asked a guy there to chase your threads. Take em a dozen doughnuts.
Later
This is a common tap. You could simply go by your local machine shop and asked a guy there to chase your threads. Take em a dozen doughnuts.
Later
#5
Full Member
iTrader: (1)
I don't know what size tap you'd need...but I'm sure it is available. They are not that expensive. I think I have an old sensor laying around, I'll grab my metric T&D set and measure the threads and let you know if you like. Ace Hardware or Sears will have the largest selection of individual T&D's unless you live near a specialty tool distributor.
Sears also carries a fractional/metric thread chaser kit for $70, may have the size needed in that...can't cut threads in raw material like a T&D...but works well. A tap will cost you a quarter of that or less. Sears has a T&D metric 39 piece set (009-52383) for $100 that includes the M18 X 1.50...then you'd have just about everything you'd need for the car except for a couple 1.00 pitch T&D's...but I don't think Mazda used a lot of fine pitch threads.
Ah, Tom beat me to it...that size tap is common. Check the above sources...you can also check their on-line sites...free delivery to store if not available in store.
Another note, Helicoil (if needed) makes a repair kit for that size thread:
http://www.bollhoff-rivnut.com/en/de...r_helicoil.php
Sears also carries a fractional/metric thread chaser kit for $70, may have the size needed in that...can't cut threads in raw material like a T&D...but works well. A tap will cost you a quarter of that or less. Sears has a T&D metric 39 piece set (009-52383) for $100 that includes the M18 X 1.50...then you'd have just about everything you'd need for the car except for a couple 1.00 pitch T&D's...but I don't think Mazda used a lot of fine pitch threads.
Ah, Tom beat me to it...that size tap is common. Check the above sources...you can also check their on-line sites...free delivery to store if not available in store.
Another note, Helicoil (if needed) makes a repair kit for that size thread:
http://www.bollhoff-rivnut.com/en/de...r_helicoil.php
Thread
Thread Starter
Forum
Replies
Last Post
rgordon1979
3rd Generation Specific (1993-2002)
40
03-15-22 12:04 PM
troym55
3rd Generation Specific (1993-2002)
23
05-25-16 12:42 PM
SakeBomb Garage
Group Buy & Product Dev. FD RX-7
8
10-09-15 10:05 PM