FD suddenly and without warning, won't start...
#26
I'm only asking questions
iTrader: (6)
Yes.
You can use a paperclip, or a small piece of wire to bridge the terminals.
The bulkhead connector the next poster is referring to is what I was saying in my post.
Do these things above, and that will give you a better idea of what's going on.
(Bridging the ports in the diagnostic box, or having someone turn the key in the ignition for a second or two will both work for your purposes.)
#29
Brap, brap, brap...
Well gentlemen, the car is running! I really appreciate all the help and attention from the community. Special mention to my friend Phil, aicrotary2 on these boards. He walked me thru the testing procedure and made it easy for me.
So, here's what we did:
- Took the electrical tape off the relay to get to the wires going to it.
- Removed the wire coming directly off the battery to the relay (87 or 30 I can't remember)
- Tested that wire and got 12v
- Removed the wire from the relay that leads to the fuel pump clip
- Removed the inline fuse from the "hot" wire off the battery
- Jumped the connectors of the direct battery wire and the fuel pump power wire to deliver a full 12v direct off the battery to the pump
- After reconnecting my battery (have a battery cut switch behind seat, and cut power for safety) I replaced the fuse and heard the pump turned on
- Replaced the wiring as it was, battery wire to 80 or 37 (can't remember) and the fuel pump power wire to its respective spot on relay
- Started the car and saw 40psi fuel pressure on my SPA gauge and 40 psi on my Aeromotive FPR, at idle
I warmed the car up to around 130F coolant temp to avoid flooding or fouling the plugs potentially, and shut the car off.
I am SOOOO HAPPY right now! It was the simplest thing and it would seem that all is well with the car and the fuel pump.
Next, I'm debating rewiring the setup. I'd like to have it look a bit more professional and perhaps more functional. It appears that the clip connector that attached the direct "hot" wire from the battery to the relay was a bit loose and wasn't making the best contact. That in of itself is a simple fix. However, I'm wondering if I re-do the wiring, if I could use higher quality connectors and techniques to ensure this won't happen again.
Thanks again to everyone who helped me figure this out. And, if anyone here has any thoughts on where to go from here, please post up.
Next on the docket is this damn Innovate wideband which only reads 7.4...??
Nick
So, here's what we did:
- Took the electrical tape off the relay to get to the wires going to it.
- Removed the wire coming directly off the battery to the relay (87 or 30 I can't remember)
- Tested that wire and got 12v
- Removed the wire from the relay that leads to the fuel pump clip
- Removed the inline fuse from the "hot" wire off the battery
- Jumped the connectors of the direct battery wire and the fuel pump power wire to deliver a full 12v direct off the battery to the pump
- After reconnecting my battery (have a battery cut switch behind seat, and cut power for safety) I replaced the fuse and heard the pump turned on
- Replaced the wiring as it was, battery wire to 80 or 37 (can't remember) and the fuel pump power wire to its respective spot on relay
- Started the car and saw 40psi fuel pressure on my SPA gauge and 40 psi on my Aeromotive FPR, at idle
I warmed the car up to around 130F coolant temp to avoid flooding or fouling the plugs potentially, and shut the car off.
I am SOOOO HAPPY right now! It was the simplest thing and it would seem that all is well with the car and the fuel pump.
Next, I'm debating rewiring the setup. I'd like to have it look a bit more professional and perhaps more functional. It appears that the clip connector that attached the direct "hot" wire from the battery to the relay was a bit loose and wasn't making the best contact. That in of itself is a simple fix. However, I'm wondering if I re-do the wiring, if I could use higher quality connectors and techniques to ensure this won't happen again.
Thanks again to everyone who helped me figure this out. And, if anyone here has any thoughts on where to go from here, please post up.
Next on the docket is this damn Innovate wideband which only reads 7.4...??
Nick
Last edited by Brilliant7-LFC; 01-12-16 at 09:55 PM.
#30
Oh yeah
One more thing. When I removed the plugs initially cause I thought it may be flooded, I only could remove the trailing plugs because the leading are those "race" plugs that I can't fit my tool on to. When looking at the plugs, they were BUR7EQP.
I've heard that running hotter plugs in the trailing is a no-no. I can't confirm but I believe the leading plugs may be 10 heat range, as the car came with an empty box of NGK plugs: B10EGV.
Are the 7's in the trailing a problem?
Car has a street ported engine, GT40 single turbo, 52 trim, .95 AR, 550/1680 injectors, stock coils, 3" exhaust turbo back, running in a Microtech LT-9C.
Your thoughts?
Nick
I've heard that running hotter plugs in the trailing is a no-no. I can't confirm but I believe the leading plugs may be 10 heat range, as the car came with an empty box of NGK plugs: B10EGV.
Are the 7's in the trailing a problem?
Car has a street ported engine, GT40 single turbo, 52 trim, .95 AR, 550/1680 injectors, stock coils, 3" exhaust turbo back, running in a Microtech LT-9C.
Your thoughts?
Nick
Thread
Thread Starter
Forum
Replies
Last Post