EGR, DP Install
#1
Senior Member
Thread Starter
Join Date: Jul 2002
Location: Canaduh, I live in an igloo duh!
Posts: 381
Likes: 0
Received 0 Likes
on
0 Posts
EGR, DP Install
I am attempting to install a DP and EGR at the same time.
For the EGR, I am not removing the intake manifold as per the website below. I have removed the airbox and all hoses and am down to the tubo manifold(Is this also called the Y-Pipe?).
The turbo manifold is in 2 parts, 1 fore, 1 aft. I have removed all of the bolts and hoses off of the forward-most section. It seems the only thing that is stopping me from removing it is some restriction in the second half since I can move it in 3 dimensions until it hits something inside of the second section.
My issue with the DP install is that the turbo manifold is in the way for me to access to top most rearward bolt on the DP. So once I get that turbo manifold removed, I should be homefree...
Any suggestions? Am I just missing something when Im attempting to remove the turbo manifold?
Thanks,
EGR Install
http://www.rx7turboturbo.com/robrobi...gr_replace.htm
Related > I broke the airpump electrical connector since it is till kinda cold up here... anyone that has one lying around please PM me.
For the EGR, I am not removing the intake manifold as per the website below. I have removed the airbox and all hoses and am down to the tubo manifold(Is this also called the Y-Pipe?).
The turbo manifold is in 2 parts, 1 fore, 1 aft. I have removed all of the bolts and hoses off of the forward-most section. It seems the only thing that is stopping me from removing it is some restriction in the second half since I can move it in 3 dimensions until it hits something inside of the second section.
My issue with the DP install is that the turbo manifold is in the way for me to access to top most rearward bolt on the DP. So once I get that turbo manifold removed, I should be homefree...
Any suggestions? Am I just missing something when Im attempting to remove the turbo manifold?
Thanks,
EGR Install
http://www.rx7turboturbo.com/robrobi...gr_replace.htm
Related > I broke the airpump electrical connector since it is till kinda cold up here... anyone that has one lying around please PM me.
#2
5yr member, joined 2001
I don't quite understand your progress. Did you remove the rear (secondary) turbo inlet, yet? You need to remove that before you can remove the y-pipe and charge elbow. I have long, skinny arms and was able to reach behind there with my small rathet and 2 1/2" extention to get the secondary inlet off.
#3
Senior Member
Thread Starter
Join Date: Jul 2002
Location: Canaduh, I live in an igloo duh!
Posts: 381
Likes: 0
Received 0 Likes
on
0 Posts
Secondary Inlet
Hey - No I havent yet. I looked at it and was like - thats not going to happen hahahha... did you get it from above or below?
#4
5yr member, joined 2001
I got it from above. There's two nuts and they're the same size as the ones holding down the y-pipe and charge elbow (10mm I think). I used a 1/4" drive ratchet with a 7" handle and a shallow socket with a 2-1/2" extension, and I had just enough room for about an eighth turn. I was able to get just enough torque on them to break them loose and remove them by hand. I couldn't see what I was doing, so I had to do it all by feel. When I was done I put them back on the same way.
#7
Full Member
Join Date: Feb 2001
Location: So farrrr away from the Land of the Rising Sun
Posts: 105
Likes: 0
Received 1 Like
on
1 Post
You do not necessarily on all 3rd gens need to take off the secondary turbo inlet pipe. When I did my DP I did take it off because many said it had to be done (plus I wanted to work on the charge control section). When I did my efini y-pipe install I did not need to take off the secondary inlet pipe, however.
Your mileage may vary.
-Kib
Your mileage may vary.
-Kib
Thread
Thread Starter
Forum
Replies
Last Post
24seven_dada
3rd Generation Specific (1993-2002)
20
11-10-18 12:03 PM
Jeff20B
1st Generation Specific (1979-1985)
73
09-16-18 07:16 PM
[For Sale] Scratch & Dent, Used, and Open-Box Sale!
SakeBomb Garage
Vendor Classifieds
5
08-09-18 05:54 PM