Check Engine Light
#1
Powered by** Rotary
Thread Starter
Check Engine Light
Tonight when i was driving around, I saw my check engine light came on. I shut it off and start it again, and the light didn't come on again. After maybe 30 min of driving, it came again and i shut if off and started again and it didn't come on for the rest of the night.
Today around maybe 11 am i washed the engine i drove it around for 30 min to dry it. Nothing happend then, but it was raining tonight and i don't know what happend. I'm gonna do check engine light diagnostics tomorrow, but does anybody have any idea what could be?
I'll post the code tomorrow here.
All comments are welcome, Thanks a lot
Today around maybe 11 am i washed the engine i drove it around for 30 min to dry it. Nothing happend then, but it was raining tonight and i don't know what happend. I'm gonna do check engine light diagnostics tomorrow, but does anybody have any idea what could be?
I'll post the code tomorrow here.
All comments are welcome, Thanks a lot
#3
Powered by** Rotary
Thread Starter
Well this morning i did the diagnostics and i got code 16. One long flash and 6 short ones. It says that code 16 is EGR (California Only), Well i live in St. Louis Missouri and What should i do about it?
Thanks
Thanks
#4
5yr member, joined 2001
If you have a '94 or '95, then it doesn't matter if it's a California car or not. The "Cali FD" applies only to the '93's. Anything later than that is basically a "Cali FD". I say get yourself a 330Ohm high-temp resistor and stick it in the end of that blue electrical connector that goes to the EGR. Then block off the EGR at your earliest convenience.
#6
5yr member, joined 2001
Originally posted by BoOsTin FD
Do you have a picture of that egr valve, I don't even know what it looks like or where is it at.
Thanks
Do you have a picture of that egr valve, I don't even know what it looks like or where is it at.
Thanks
It's a PITA to get to, but I did the EGR block off alone, and I hadn't had an iota of auto mechanics experience before this. To get to it you will need to remove the secondary (rear) turbo inlet and y-pipe. If you've got long, thin arms and a small ratchet, then you don't even need to go under the car to get the rear turbo inlet off.
Last edited by JONSKI; 09-15-02 at 12:19 PM.
#7
Junior Member
Join Date: Aug 2001
Location: drag strips
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
BoOsTin FD or anyone,
Sorry to intrude, but I'm also experiencing a check engine light. How do I do the check engine light diagnostics? What I mean is, in my honda, the ecu conviently has a led light build in it which would blink codes if something went wrong. I didn't notice any led light on the Rx-7 ecu. Do I have to buy a tool or bring it to a shop to find out whats the cause of my check engine light?
Please help, thanks...
Sorry to intrude, but I'm also experiencing a check engine light. How do I do the check engine light diagnostics? What I mean is, in my honda, the ecu conviently has a led light build in it which would blink codes if something went wrong. I didn't notice any led light on the Rx-7 ecu. Do I have to buy a tool or bring it to a shop to find out whats the cause of my check engine light?
Please help, thanks...
Trending Topics
#8
I had the same prob with code 16 flashing once the car warmed up. I was gonna block it off later. I installed the pettit grounding kit which came with one of my orders and light has not flashed since. The grounding kit give the car and ECU a lot better ground. If you do get the kit be sure to do part 2 in the instructions and use the supplied bolt to ground it to the engine block.
#9
Powered by** Rotary
Thread Starter
Originally posted by dragger
BoOsTin FD or anyone,
Sorry to intrude, but I'm also experiencing a check engine light. How do I do the check engine light diagnostics? What I mean is, in my honda, the ecu conviently has a led light build in it which would blink codes if something went wrong. I didn't notice any led light on the Rx-7 ecu. Do I have to buy a tool or bring it to a shop to find out whats the cause of my check engine light?
Please help, thanks...
BoOsTin FD or anyone,
Sorry to intrude, but I'm also experiencing a check engine light. How do I do the check engine light diagnostics? What I mean is, in my honda, the ecu conviently has a led light build in it which would blink codes if something went wrong. I didn't notice any led light on the Rx-7 ecu. Do I have to buy a tool or bring it to a shop to find out whats the cause of my check engine light?
Please help, thanks...
Hope this helps
Regarding my problem, I don't know what happend but the light doesn't come on anymore. I guess if i messed it up when i washed the engine, maybe now it's dryed out or something. I hope it stays this way. If it doesn't come on tomorrow i guess i don't have to worry about it.
#10
There and back again
Join Date: Feb 2001
Location: Camarillo, Ca
Posts: 967
Likes: 0
Received 0 Likes
on
0 Posts
Just in case it comes back (and it will if it is a cali model) I wrote this littl' diddy a while back for just your problem.
EGR cure so simple
EGR cure so simple
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM