Banzai Racing block off plates question
#1
Senior Member
Thread Starter
iTrader: (5)
Join Date: Apr 2012
Location: USA
Posts: 278
Likes: 0
Received 0 Likes
on
0 Posts
Banzai Racing block off plates question
hi, i've seen a lot of talk about block off plates but i haven't really found any thread that explains the reasoning and benefits of using block off plates
the one i'm referring to is this: http://www.banzai-racing.com/store/F...ff_plates.html
i have a 1993 FD, 5 speed, all stock, it's a california car but i'm not worried about emissions components (off road use car, won't need smog), my main goal is to remove as many messy engine bay components while maintaining driveability.
any obvious reasoning behind removing these components and adding block off plates?
any down sides, other than emissions?
any benefits?
the one i'm referring to is this: http://www.banzai-racing.com/store/F...ff_plates.html
i have a 1993 FD, 5 speed, all stock, it's a california car but i'm not worried about emissions components (off road use car, won't need smog), my main goal is to remove as many messy engine bay components while maintaining driveability.
any obvious reasoning behind removing these components and adding block off plates?
any down sides, other than emissions?
any benefits?
#2
Torqueless Wonder
iTrader: (1)
the block off plates blocks off the emissions components.
it simplifies the engine bay quite a bit. theres really no other benefit than having more room to work in as well as less things to go wrong, so less headaches.
you can look into the excessive LIM if you're willing to spend a bit of money
it simplifies the engine bay quite a bit. theres really no other benefit than having more room to work in as well as less things to go wrong, so less headaches.
you can look into the excessive LIM if you're willing to spend a bit of money
#3
Senior Member
Thread Starter
iTrader: (5)
Join Date: Apr 2012
Location: USA
Posts: 278
Likes: 0
Received 0 Likes
on
0 Posts
the block off plates blocks off the emissions components.
it simplifies the engine bay quite a bit. theres really no other benefit than having more room to work in as well as less things to go wrong, so less headaches.
you can look into the excessive LIM if you're willing to spend a bit of money
it simplifies the engine bay quite a bit. theres really no other benefit than having more room to work in as well as less things to go wrong, so less headaches.
you can look into the excessive LIM if you're willing to spend a bit of money
#4
Torqueless Wonder
iTrader: (1)
Yup.
Since the ECU is not flashable, you'll need to get a PFC at the least. They go for about $300-600.
If you're lucky you can get a Pettit chipped ECU in the classifies and they are virtually dirt cheap and are decently effective.
Once you install the block off plates, you'll need to find some resistors for the connectors that once attached to the emissions components so the stock ECU doesnt go into limp mode. Search for a thread about it as the resistors are specific.
Since the ECU is not flashable, you'll need to get a PFC at the least. They go for about $300-600.
If you're lucky you can get a Pettit chipped ECU in the classifies and they are virtually dirt cheap and are decently effective.
Once you install the block off plates, you'll need to find some resistors for the connectors that once attached to the emissions components so the stock ECU doesnt go into limp mode. Search for a thread about it as the resistors are specific.
#5
Rx7 Wagon
iTrader: (16)
You don't necessarily need an aftermarket ecu to remove emissions and run block off plates. The ecu will throw codes if you don't put resistors in place.
Having an aftermarket ecu makes it less of a headache, but then if you don't simplify your engine harness you'll have half a dozen loose connectors.
There's not a lot of advantage to diving into this right off the bat, especially if it's all functioning correctly.
Having an aftermarket ecu makes it less of a headache, but then if you don't simplify your engine harness you'll have half a dozen loose connectors.
There's not a lot of advantage to diving into this right off the bat, especially if it's all functioning correctly.
Trending Topics
#8
I'm sorry to revive this post, but I have a simple question. I ordered the kit from Banzai with the intent of only getting rid of the AWS because the original owner disconnected the hose form the intake pipe but that is all he did. He did not block off the AWS.
Can someone tell me if doing this will cause any issues or check engine lights or anything else I should do besides just using the AWS block off.
I plan on using the other block offs if I ever replace the engine with a ported engine and get the PFC.
Thanks for any input.
Can someone tell me if doing this will cause any issues or check engine lights or anything else I should do besides just using the AWS block off.
I plan on using the other block offs if I ever replace the engine with a ported engine and get the PFC.
Thanks for any input.
#10
I was thinking of just blocking off the pipe with a block off plate but leaving the AWS connected. They just have the pipe disconnected.
#11
cuz everyone's 99...
iTrader: (9)
The only thing I'd add is maybe a new OEM gasket that goes between the hardpipe (which connects to the soft pipe) and the UIM. Put it between the block off plate and the UIM to ensure no leak.
I will be doing this soon myself
Thread
Thread Starter
Forum
Replies
Last Post
CaptainKRM
2nd Generation Specific (1986-1992)
14
08-26-15 09:52 PM