3rd Gen General Discussion The place for non-technical discussion about 3rd Gen RX-7s or if there's no better place for your topic

Losing Power 1995 FD

Old Oct 27, 2020 | 07:16 PM
  #1  
jigistheman's Avatar
Thread Starter
Junior Member
 
Joined: May 2017
Posts: 12
Likes: 0
From: japan
Question Losing Power 1995 FD

Good Morning from Guam. I haven't posted in a while. I recently shipped my car from Japan to Guam. 1995 FD. It has been my daily for the last 3 years. I am having issues and need help. At first I noticed I was not getting full power when trying to push my car a little bit. It was bogging down and felt like i was not getting enough gas. I changed spark plugs, fluids, checked all grounds. It was running good for a couple of days but now when i was driving home yesterday, my car turned off completely. I was able to start it up right after and right before i pulled into my garage it shut off again. what could it be? I am not sure why i am losing power in the middle of driving. it is very unsafe and would like to remedy the situation before i take it out again. Car is mostly stock except exhaust and intake. 93,000 km. thanks in advance.
Reply
Old Oct 28, 2020 | 08:03 AM
  #2  
madhat1111's Avatar
Full Member
Tenured Member: 5 Years
Liked
Loved
Community Favorite
 
Joined: Aug 2020
Posts: 244
Likes: 90
From: Arizona
Not as an Rx-7 expert, but just curious since you feel like it's short on fuel, when's the last time you changed the fuel filter? Have you checked the fuel pressure?
Also, does this sound similar? Might be some more ideas.
https://www.rx7club.com/3rd-generati.../#post12440982

Last edited by madhat1111; Oct 28, 2020 at 08:06 AM.
Reply
Old Oct 28, 2020 | 09:01 AM
  #3  
DaleClark's Avatar
RX-7 Bad Ass
Tenured Member: 20 Years
Liked
Loved
Community Favorite
iTrader: (56)
 
Joined: Jan 2002
Posts: 15,622
Likes: 2,725
From: Pensacola, FL
Do a compression test before you go further to make sure the engine is good before troubleshooting things to death.

Dale
Reply
Old Oct 28, 2020 | 05:27 PM
  #4  
jigistheman's Avatar
Thread Starter
Junior Member
 
Joined: May 2017
Posts: 12
Likes: 0
From: japan
i am following that post as well. we are having similar issues but my car shuts off with no warning in the middle of driving, i think that is the only difference. but i did check pressure and changed filter. thank you for your input.
Reply
Old Oct 28, 2020 | 05:28 PM
  #5  
jigistheman's Avatar
Thread Starter
Junior Member
 
Joined: May 2017
Posts: 12
Likes: 0
From: japan
Originally Posted by DaleClark
Do a compression test before you go further to make sure the engine is good before troubleshooting things to death.

Dale
i was planning on doing that this weekend. thank you for your help.
Reply
Old Oct 29, 2020 | 12:04 PM
  #6  
SpinningDorito's Avatar
Senior Member
iTrader: (2)
 
Joined: Jan 2018
Posts: 482
Likes: 81
From: TX
I think the takeaway from the other thread right now should be to check your ECU for any error codes.
Reply
Old Nov 1, 2020 | 10:29 PM
  #7  
jigistheman's Avatar
Thread Starter
Junior Member
 
Joined: May 2017
Posts: 12
Likes: 0
From: japan
Originally Posted by SpinningDorito
I think the takeaway from the other thread right now should be to check your ECU for any error codes.
I am getting codes 44 and 14. looks like i need a new solenoid (turbo control). are there any other parts i might need to upgrade before i open her up?
Reply
Old Nov 4, 2020 | 11:17 AM
  #8  
Trinityevo13's Avatar
Full Member
Tenured Member 05 Years
iTrader: (1)
 
Joined: Jan 2016
Posts: 243
Likes: 14
From: Florida
Hey, check the ground to the ECU as well. I had corrosion on mine and noticed a difference after cleaning it up

cheers
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
superstock2
3rd Generation Specific (1993-2002)
48
Jan 2, 2021 12:27 AM
Liehry
General Rotary Tech Support
2
Jun 12, 2010 08:33 AM
obie81
General Rotary Tech Support
1
May 15, 2007 09:24 AM
jimshih
3rd Generation Specific (1993-2002)
6
Aug 9, 2006 11:06 AM


Thread Tools
Search this Thread

All times are GMT -5. The time now is 09:13 AM.