2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.

Won't Start-need suggestions

Thread Tools
 
Search this Thread
 
Old Jun 4, 2010 | 01:14 PM
  #1  
freq's Avatar
Thread Starter
Senior Member
Tenured Member 15 Years
iTrader: (6)
 
Joined: Jan 2006
Posts: 692
Likes: 2
From: North Carolina
Won't Start-need suggestions

I recently rebuilt my s4 turbo.
The starter turns the engine over, but it wont fire.
I checked the plugs--they have spark.
I checked to make sure it's getting fuel.
I quadruple checked all of my wiring and connections.

It was sitting for over a year before I rebuilt it.
It's got fresh gasoline.

Any ideas?
Reply
Old Jun 4, 2010 | 02:44 PM
  #2  
driftxsequence's Avatar
Rotisserie Engine
Tenured Member: 15 Years
Liked
Loved
Community Favorite
iTrader: (8)
 
Joined: Jan 2007
Posts: 1,944
Likes: 107
From: Wilmington, DE
you checked for fuel, you checked for spark, how about air? are your plugs good?
Reply
Old Jun 4, 2010 | 05:39 PM
  #3  
freq's Avatar
Thread Starter
Senior Member
Tenured Member 15 Years
iTrader: (6)
 
Joined: Jan 2006
Posts: 692
Likes: 2
From: North Carolina
Originally Posted by driftxsequence
you checked for fuel, you checked for spark, how about air? are your plugs good?
Plugs r good. Checked for fuel and spark. I assume air's ok. Air Filter's clean.
Reply
Old Jun 4, 2010 | 06:15 PM
  #4  
satch's Avatar
Moderator
Tenured Member: 20 Years
iTrader: (1)
 
Joined: Jun 2005
Posts: 11,738
Likes: 16
From: tulsa,ok.
Have you checked to see if the flapper on the AFM is opening upon startup? Have you tried spraying some starter fluid for a few seconds into the air intake cowl and trying to start the car?
Reply
Old Jun 4, 2010 | 06:29 PM
  #5  
RXnos1200's Avatar
1200 gone......but......
Tenured Member 05 Years
iTrader: (24)
 
Joined: Oct 2006
Posts: 902
Likes: 0
From: so cal
try building up the compression abit since it a fresh rebuild with some oil. put it in through the leading spark plug holes....

WARNING......will smoke the whole place out...

can also remove the efi fuse and crank the engine over. (pulling the fuse helps the motor from flooding out)....... put the fuse back in after

the engine cranks and see if it helps to start the engine. good luck.......
Reply
Old Jun 4, 2010 | 08:55 PM
  #6  
driftxsequence's Avatar
Rotisserie Engine
Tenured Member: 15 Years
Liked
Loved
Community Favorite
iTrader: (8)
 
Joined: Jan 2007
Posts: 1,944
Likes: 107
From: Wilmington, DE
use regular motor oil and not ATF, ATF will eat your rubber seals up.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Snook
Single Turbo RX-7's
39
Oct 4, 2015 08:47 PM
PinkRacer
2nd Generation Specific (1986-1992)
43
Oct 1, 2015 09:13 AM
1NSIGHT
Drifting
8
Sep 29, 2015 12:18 PM
JGLawson
General Rotary Tech Support
4
Sep 13, 2015 03:23 PM
younG_Gunner
2nd Generation Specific (1986-1992)
2
Sep 9, 2015 08:26 PM




All times are GMT -5. The time now is 10:25 PM.