2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.
Sponsored by:

while I had my shifter out... can I replace this?

Thread Tools
 
Search this Thread
 
Old 01-20-04, 08:38 PM
  #1  
illegal ninja moves

Thread Starter
 
tie pilot's Avatar
 
Join Date: Dec 2003
Location: Gainesville, Florida
Posts: 544
Likes: 0
Received 0 Likes on 0 Posts
while I had my shifter out... can I replace this?

I did a search for this and was able to find a picture that should help make my question clear...

I had the shifter out of my 1990 GXL 5-speed and I noticed this sort of groove in the bottom of the shifter. This groove was lined with some type of orange plastic and it fit over a pin towards the front of the tranny.

I could see that some of the plastic had been broken off, and I carelessly chipped away even MORE of the orange plastic when I had the stick out. Sure enough, when I put the shifter back in, I found that shifts are pretty rough sometimes (worse than before).

I've seen lots of posts concerning the shifter bushing, but I'm pretty sure that's NOT this part I'm looking for. So here's the pic.

Can this plastic lining be replaced? Where can I get it? Dealership?
Old 01-20-04, 08:55 PM
  #2  
truespin, not tirespin

 
truespin88's Avatar
 
Join Date: Nov 2003
Location: Belpre, Ohio
Posts: 655
Likes: 0
Received 0 Likes on 0 Posts
My car didn't have anything orange on it anywhere. It had a purple bushing in there, and I added the white bushing. Shifts awesomely.
Old 01-20-04, 09:08 PM
  #3  
illegal ninja moves

Thread Starter
 
tie pilot's Avatar
 
Join Date: Dec 2003
Location: Gainesville, Florida
Posts: 544
Likes: 0
Received 0 Likes on 0 Posts
i see... so you know where to buy them then?
Old 01-20-04, 09:19 PM
  #4  
truespin, not tirespin

 
truespin88's Avatar
 
Join Date: Nov 2003
Location: Belpre, Ohio
Posts: 655
Likes: 0
Received 0 Likes on 0 Posts
I got my white bushing at Mazdatrix. Cost like 10 bucks or so. Not bad. I must repeat, it shifts famously. And all of my gears are tight and precise.
Old 01-20-04, 09:20 PM
  #5  
Rotorhead

 
Evil Aviator's Avatar
 
Join Date: Feb 2001
Location: Charlottesville, Virginia, USA
Posts: 9,136
Likes: 0
Received 39 Likes on 33 Posts
http://www.mazdatrix.com/faq/shiftbsh.htm
Old 01-20-04, 09:20 PM
  #6  
Dak
Information Regurgitator

 
Dak's Avatar
 
Join Date: Feb 2001
Location: Sparta TN. United States
Posts: 1,893
Received 172 Likes on 129 Posts
Try Mazdatrix.They're usually cheaper than the dealer.

http://www.mazdatrix.com
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
rgordon1979
3rd Generation Specific (1993-2002)
40
03-15-22 12:04 PM
whinin
Introduce yourself
17
03-30-19 07:53 PM
Apoc3D
2nd Generation Specific (1986-1992)
10
09-05-15 10:24 AM



Quick Reply: while I had my shifter out... can I replace this?



All times are GMT -5. The time now is 06:54 AM.