Turn Signal Issues
#26
Former Moderator. RIP Icemark.
Originally Posted by staticguitar313
no suggestions?
and I wouldn't swap the whole 91, too many glitches in the electrical system (S5 electrical systems make the S4 system look like Toyota designed it).
#27
Alright, i'm pretty much screwed though, i'm no good at this kinda of diganosis, electrical that is and this car HAS to be street legal i'll try inspecting the harness and bulbs etc. a bad connector at a light wouldnt make the entire system fail would it? Maybe a ground loose?
#28
Former Moderator. RIP Icemark.
well, it doesn't get any more basic:
If they are not working on both the turn and the hazards, then either the CPU is bad, the power is bad, the output from the CPU is bad, or the wires are not connected to the lights.
And if you can't go to Home Depot or Radio shack to get at least a $20 meter (something that every single person that works on cars should have) to test the wires to see which one of the above has the problem... well yeah, you are screwed.
If they are not working on both the turn and the hazards, then either the CPU is bad, the power is bad, the output from the CPU is bad, or the wires are not connected to the lights.
And if you can't go to Home Depot or Radio shack to get at least a $20 meter (something that every single person that works on cars should have) to test the wires to see which one of the above has the problem... well yeah, you are screwed.
#30
Full Member
Join Date: Sep 2002
Location: Anchorage, AK
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
Check the CPU again, not the one on the passenger floor board, but the body CPU that's under the drivers side of the dash near your left leg. Take it out and open it up, make sure that there is no bad solder joints. I had that problem and re-soldered it, now it works. Just a suggestion, not sure if you are talking about swapping the main ECM into the other car, or the actual body CPU.
#32
Former Moderator. RIP Icemark.
Originally Posted by staticguitar313
i guess i'm grabbing a decent DMM then ^_^
then we can start testing the outputs.
#34
D1 Drifter Status
Join Date: Dec 2004
Location: Sacramento CA
Posts: 484
Likes: 0
Received 0 Likes
on
0 Posts
Im glad your posted this, cause i tried awhile ago, and got NO replies.
Im haveing almost the exact same problem.
My Left hand blinkers do not work. bulbs are brand new, hazards only turn the right side blinkers on. the switch only turns the right side blinkers on.
I hear a clicking for the left side.
Same deal as static?
Im haveing almost the exact same problem.
My Left hand blinkers do not work. bulbs are brand new, hazards only turn the right side blinkers on. the switch only turns the right side blinkers on.
I hear a clicking for the left side.
Same deal as static?
#35
Former Moderator. RIP Icemark.
Originally Posted by reatrdedspleen
Im glad your posted this, cause i tried awhile ago, and got NO replies.
Im haveing almost the exact same problem.
My Left hand blinkers do not work. bulbs are brand new, hazards only turn the right side blinkers on. the switch only turns the right side blinkers on.
I hear a clicking for the left side.
Same deal as static?
Im haveing almost the exact same problem.
My Left hand blinkers do not work. bulbs are brand new, hazards only turn the right side blinkers on. the switch only turns the right side blinkers on.
I hear a clicking for the left side.
Same deal as static?
#36
D1 Drifter Status
Join Date: Dec 2004
Location: Sacramento CA
Posts: 484
Likes: 0
Received 0 Likes
on
0 Posts
I know this thread is sorta old. but, i have some questions. Static did you ever get the problem fixed? and Icemark. Will an S4 cpu flasher board, or the whole cpu work in an S5 car. Ive pulled my bored out, and im unable to see any bad solder joints, so im considering just getting a whole nother cpu from another 7
#37
Winter sucks
Join Date: Jan 2004
Location: Newberg, Oregon
Posts: 3,083
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Icemark
The Turn signal circuit board and plug is the same in all FC and FD CPUs regardless of series.
However the turn signal switches are not.
However the turn signal switches are not.
I know this thread is sorta old. but, i have some questions. Static did you ever get the problem fixed? and Icemark. Will an S4 cpu flasher board, or the whole cpu work in an S5 car. Ive pulled my bored out, and im unable to see any bad solder joints, so im considering just getting a whole nother cpu from another 7
#38
D1 Drifter Status
Join Date: Dec 2004
Location: Sacramento CA
Posts: 484
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by micaheli
Yes.. see above comment from Icemark.
TY for pointing me to that
#40
everything will be okay
iTrader: (15)
Join Date: Oct 2005
Location: Cedar Rapids, IA
Posts: 1,650
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by POWERFC3S
i have the same issue with my S5....my hazard work..but only right turn dont'work..and i can hear fast click noise when i turn it on...
#41
everything will be okay
iTrader: (15)
Join Date: Oct 2005
Location: Cedar Rapids, IA
Posts: 1,650
Likes: 0
Received 0 Likes
on
0 Posts
k, nevermind. just got back from walmart. got bulbs for the signals and noticed the 2 filiments in them. i just couldnt see my old bulb cause it was coated in yellow.
Thread
Thread Starter
Forum
Replies
Last Post
rx8volks
Canadian Forum
0
09-01-15 11:02 PM