TII engine will not REV over 3000k (search no help, not clogged cat)
#1
Banned. I got OWNED!!!
Thread Starter
Join Date: Nov 2001
Location: charlotte
Posts: 625
Likes: 0
Received 0 Likes
on
0 Posts
TII engine will not REV over 3000k (search no help, not clogged cat)
I finally got the car running a few days ago, but it still isnt right...
It idles very strong, a little on the high side, but I dont care about fixing that now.
My problem is that the engine will not rev over ~3500 RPMs. When I put pedal to floor, the engine sounds like its choking.
Pre and main cats are gutted, so thats not the problem. Could it be intake leaks? I spent a lot of time making sure nothing would leak, but cannot rule that out.
Tomorrow I guess I'll compression check it and get some starter fluid or something to test for intake leaks.
Heres some info bout car if helpful at all w/ this problem.
90 jspec in 87 car w/ 87 electronics and injectors, just put engine in last week
all emmissions removed and blocked off
BAC removed, 2 throttle plates removed, thermowax removed
secondary injectors just rebuilt/blueprint/balanced
Also, I'm new to turbos. Is it supposed to pull vacuum at idle? I pulled vacuum line off and it was pushing air, not sucking.
It idles very strong, a little on the high side, but I dont care about fixing that now.
My problem is that the engine will not rev over ~3500 RPMs. When I put pedal to floor, the engine sounds like its choking.
Pre and main cats are gutted, so thats not the problem. Could it be intake leaks? I spent a lot of time making sure nothing would leak, but cannot rule that out.
Tomorrow I guess I'll compression check it and get some starter fluid or something to test for intake leaks.
Heres some info bout car if helpful at all w/ this problem.
90 jspec in 87 car w/ 87 electronics and injectors, just put engine in last week
all emmissions removed and blocked off
BAC removed, 2 throttle plates removed, thermowax removed
secondary injectors just rebuilt/blueprint/balanced
Also, I'm new to turbos. Is it supposed to pull vacuum at idle? I pulled vacuum line off and it was pushing air, not sucking.
#2
Rotary Powered
iTrader: (2)
Re: TII engine will not REV over 3000k (search no help, not clogged cat)
Originally posted by niner
just put engine in last week
just put engine in last week
good luck
#5
Banned. I got OWNED!!!
Thread Starter
Join Date: Nov 2001
Location: charlotte
Posts: 625
Likes: 0
Received 0 Likes
on
0 Posts
well, I dont think I'm hitting 8.6 psi or whatever fuel cut is at below 3000rpms
I got extra grounds running all over the engine bay, but I might try re-grounding the ECU tomorrow
thanks for ideas, any more?
I got extra grounds running all over the engine bay, but I might try re-grounding the ECU tomorrow
thanks for ideas, any more?
#7
Banned. I got OWNED!!!
Thread Starter
Join Date: Nov 2001
Location: charlotte
Posts: 625
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by SonicRaT
Won't go anywhere past 3K, is the timing on?
timing is not the problem
Does it stop instantly at 3k, or will it go a tad higher and come down?
thats another problem, there is a short in my "meter" circuit, so fuse keeps blowing and tach dont work. when I floor the gas pedal, it will go to about 3k (I estimate) and stumble around a bit like its choking. I need to find that damn short soon too
Is your AFM functioning?
AFM was one of the things I am definately going to be checking out tomorrow. The flapper door is pointing down b/c of the mounting kit that came w/ my intake but I understand that it should still work correctly pointing down. hopefully I'll be able to take one off another car and see what happens
I'm just trying to get as many ideas as possible before I start working on it again tomorrow
Won't go anywhere past 3K, is the timing on?
timing is not the problem
Does it stop instantly at 3k, or will it go a tad higher and come down?
thats another problem, there is a short in my "meter" circuit, so fuse keeps blowing and tach dont work. when I floor the gas pedal, it will go to about 3k (I estimate) and stumble around a bit like its choking. I need to find that damn short soon too
Is your AFM functioning?
AFM was one of the things I am definately going to be checking out tomorrow. The flapper door is pointing down b/c of the mounting kit that came w/ my intake but I understand that it should still work correctly pointing down. hopefully I'll be able to take one off another car and see what happens
I'm just trying to get as many ideas as possible before I start working on it again tomorrow
Last edited by niner; 05-31-02 at 11:18 PM.
Trending Topics
#9
Banned. I got OWNED!!!
Thread Starter
Join Date: Nov 2001
Location: charlotte
Posts: 625
Likes: 0
Received 0 Likes
on
0 Posts
Hard to say, since I've only run it a couple of times since I put the engine in. I'd say a tad rich though, b/c the O2 sensor was covered in a fresh coat of black stuff when I took off exhaust earlier. The primaries are a little leaky too.
Thread
Thread Starter
Forum
Replies
Last Post
Megasquirt timing map and EGt ?? what do you guys think
immanuel__7
Megasquirt Forum
3
08-22-15 09:34 PM
KAL797
Test Area 51
0
08-11-15 03:47 PM